Rimage Professional 3410 Einrichtungs- Und Installationsanleitung

Rimage Professional 3410 Setup and Installation
®
Guide
Before you begin:
This document describes how to set up your Rimage Professional 3410 system to run
with Rimage Software Suite version 8.6 and higher. The 3410 is part of the Rimage
Professional series of Disc Publishing systems.
The instructions in this document are intended for people who are familiar with
hardware setup, software installation, and Windows® operating systems. If you do not
understand the procedures in this document, ask your computer technician for help.
Documents referenced in this procedure are found on the Rimage Professional
3410/5410N User Guide disc included with your system and are also available online
at www.rimage.com/support. From the Support menu select: Professional Series >
Professional 3410N > User Manuals tab.
Important!
• Read all setup instructions thoroughly before you begin.
• Save all packing boxes and packing materials for your Rimage system.
Notes:
• The 3410 is a non-embedded autoloader and integrated Everest
that requires an external PC to be used as the control center. The external
PC does not ship with the 3410. Refer to the Rimage Professional 3410 and
5410 Specifications document at www.rimage.com/support
requirements.
• Your product may not look exactly like the product pictured.
• You must have administrative privileges to install the Rimage Software Suite.
You will also need administrative privileges to operate Rimage Software Suite—
Standalone.
• The term "autoloader" is used throughout this document to refer to the Rimage
Professional 3410N. The term "printer" refers to the integrated Everest 400
printer. The term "system" refers to the combination of the Professional 3410
autoloader and the Everest 400 printer.
• This product is also designed for an IT power distribution system with phase-to-
phase voltage 120/230V.
• Unless otherwise indicated, all Windows navigation statements are Windows 7
paths. Other operating systems' navigation paths may differ slightly.
2002544_A
Items needed:
• A network cable is needed if you plan on submitting jobs or accessing files
from a networked PC.
A network cable is mandatory if you are running Rimage Software
ƒ
Suite—Network using default settings.
A network cable is optional if you are running Rimage Software Suite—
ƒ
Standalone.
Important! You must provide a network cable. A network cable is not
included with the system.
1
Verify the contents of the Accessory Kit
The Accessory Kit contains:
• Rimage Professional 3410 Setup and Installation Guide (this document)
• Rimage Product Warranty/Guarantee
• A/C cord
• USB cable
• Rimage Professional 3410/5410N User Guide disc
• Disc holder with Rimage Software Suite—Standalone or Rimage Software
Suite—Network software disc
• Sample disc
2
Prepare the autoloader
Important! The system is heavy. Use
assistance when lifting the system.
a. Remove the tape and packing foam
from the top and side of the autoloader.
TM 400 printer
for minimum PC
b. Open the front door.
c. Remove the plastic packing brace from the
lift arm.
d. Remove the plastic packing brace from the
printer tray.
i. Remove the tape from the printer tray.
ii. Lower the printer door and rotate the
plastic packing clockwise to remove.
Note: you may need to bend the plastic
brace in the printer tray slightly to
remove it.
e. Close the front door.
Tape and Packing
Foam
Tape and
Packing Foam
Plastic Packing
Braces and Tape
Copyright © 2012 Rimage
3
Prepare the Everest 400 printer
Pull up on the printer cover latch.
a.
b. Lower the printer cover to expose the ribbon
carriers.
4
Remove the ribbon carriers
Note: For more detailed instructions on installing the print and
retransfer ribbons, refer to our YouTube channel at
RimageCorp for instructional videos or refer to the Rimage Professional 3410
and 5410N User Guide.
a. Turn the center latch counter-clockwise to unlock it.
b. Pull the print ribbon carrier and the retransfer ribbon carrier to remove
them from the printer.
Print Ribbon
Carrier
Center
Retransfer Ribbon
Latch (Locked Position)
Carrier
5
Remove the retransfer ribbon packing
a. Remove the tape and plastic
brace from the front of the
carrier.
b. Remove tape and plastic
Tape and
packaging from around the
Plastic Brace
outside of the carrier.
6
Install the retransfer ribbon
a. With the supply roll on the left side, and the takeup roll on the right side,
unroll a few inches of ribbon and lay the ribbon on a clean, flat surface.
b. Place the retransfer ribbon carrier on top of the exposed ribbon.
c. Place the supply roll on the carrier with the large end in the hole and
push down to snap the roll into place.
d. Place the takeup roll on the carrier with the
large end in the hole and push down to snap
the roll into place.
e. Return the retransfer ribbon carrier to the
autoloader.
www.youtube.com/user/
Center Latch
(Unlocked Position)
Tape and
Plastic
Packaging
Takeup Roll
Supply Roll
Page 1