Activity Tracking - Bosch Kiox BUI330 Originalbetriebsanleitung

English – 4​
Setting the assistance level
On the operating unit (7), you can set the level of assistance
you want the eBike drive to provide you with while pedalling.
The assistance level can be changed at any time, even while
cycling.
Note: In some models, the assistance level may be preset
and cannot be changed. There may also be fewer assistance
levels available than stated here.
The following assistance levels are available as a maximum:
– OFF: Motor assistance is switched off. The eBike can just
be moved by pedalling, as with a normal bicycle. The
push assistance cannot be activated at this assistance
level.
– ECO: Effective assistance with maximum efficiency, for
maximum range
– TOUR: Steady assistance, long range for touring
– SPORT/eMTB:
SPORT: Powerful assistance, for mountain biking and
cycling in urban traffic
eMTB: Optimum assistance whatever the terrain, rapid
acceleration when starting from a standstill, improved dy-
namics and top performance (eMTB only available in
combination with the drive units BDU250P CX, BDU365,
BDU450 CX and BDU480 CX. A software update may be
required.)
– TURBO: Maximum assistance even at high pedalling
speeds, for sport cycling
To increase the assistance level, press the + (12) button on
the operating unit repeatedly until the desired assistance
level appears on the display. To decrease the assistance
level, press the – (11) button.
The requested motor output appears on the display h. The
maximum motor output depends on the selected assistance
level.
If the on-board computer is removed from the holder (5),
the assistance level that was last displayed for the battery is
saved.
Switching the push assistance on/off
The push assistance aids you when pushing your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 6 km/h. The lower the selected gear,
the lower the speed of the push assistance function (at full
power).
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To activate the push assistance, briefly press the WALK
button on your on-board computer. After activation, press
the + button within 3 s and keep it pressed. The eBike drive
is switched on.
Note: The push assistance cannot be activated at assistance
level OFF.
1 270 020 XBK | (12.03.2019)
The push assistance is switched off as soon as one of the
following occurs:
– You release the + button;
– The wheels of the eBike are locked (e.g. by applying the
brakes or hitting an obstacle);
– The speed exceeds 6 km/h.
The push assistance function is subject to local regulations;
the way it works may therefore differ from the description
above, or the function may even be deactivated completely.
Switching bicycle lights on/off
On the model in which the lighting is powered by the eBike
system, the front and rear lights can be switched on and off
at the same time via the on-board computer using the bike
light button (3).
With the light switched on, the lighting c indicator (see "Start
page", page English – 6) appears in the status bar on the
display.
Switching the bike lights on and off has no effect on the
backlighting of the display.
Creating a user ID
In order to use all the features of the operating system, you
must also register online.
With a user ID, you can analyse your ride data and routes,
among other things.
You can set up a user ID via your Bosch eBike Connect
smartphone app or simply at www.eBike-Connect.com.
Enter the details required for registration. The Bosch eBike
Connect smartphone application is available to download
free of charge from the App Store (for Apple iPhones) or
from the Google Play store (for Android devices).
Connecting to the on-board computer using the
Bosch eBike Connect app
Follow these steps to establish a connection to your smart-
phone:
– Load the app.
– Select the tab <My eBike>.
– Select <Add new eBike device>.
– Add Kiox.
The app will then display an instruction to press and hold the
bike lighting button (3) on the on-board computer for
five seconds.
Press and hold the button (3) for at least five seconds. The
on-board computer automatically activates the
Bluetooth® Low Energy connection and switches to pairing
mode.
Follow the instructions on the screen. Once pairing is com-
plete, the user data is synchronised.
Note: The Bluetooth® connection does not have to be activ-
ated manually.
Bosch eBike Systems

Activity tracking

In order to record activities, you must be registered with and
logged into the eBike Connect portal and the eBike Connect
app.
To record activities, you must consent to the storage of your
location data either in the portal or the app. Without this,
your activities will not be shown in the portal or the app.
Your position is only recorded if the on-board computer is
connected to the eBike Connect app.
Once synchronisation is complete, the activities will be dis-
played in the app and in the portal.
eShift (optional)
eShift is the integration of electronic gear-shifting systems
into the eBike system. The eShift components are electric-
ally connected to the drive unit by the manufacturer. The
separate operating instructions describe how to operate the
electronic gear-shifting systems.
eSuspension (optional)
eSuspension is the integration of electronic shock absorp-
tion and suspension elements into the eBike system. You
can use the Quick Menu to select predefined settings for the
eSuspension system.
For details of these settings, please refer to the operating in-
structions provided by the eSuspension manufacturer.
eSuspension is only available in combination with the Kiox
on-board computer and can only be used with the BDU450
CX, BDU480 CX and BDU490P drive units.
ABS – anti-lock braking system (optional)
If the wheel is fitted with a Bosch eBike ABS with no external
control lights, the control lights will be shown on the display
when the system starts and in the event of a fault. For de-
tailed information on the ABS and how it works, please refer
to the ABS operating instructions.
Lock (premium function)
You can buy this function from the <Shop> in the eBike Con-
nect app. Once the Lock function is switched on, the eBike
drive unit assistance is deactivated. It can only then be activ-
ated using the on-board computer associated with the eBike.
Detailed operating instructions can be found online at
www.Bosch‑eBike.com/Kiox‑manual.
Software updates
Software updates are transferred to the on-board computer
in the background of the app as soon as it is connected to
the app. When an update is complete, this will be displayed
the next three times the on-board computer is restarted.
Alternatively, you can check in the <Sys settings> whether
an update is available.
Bosch eBike Systems
English – ​ 5
Powering external devices via the USB port
The USB port can be used to operate or charge most devices
that can be powered via USB (e.g. various mobile phones).
Charging requires the on-board computer to be mounted
and a sufficiently charged battery to be inserted in the eBike.
Open the protective cover (17) for the USB port on the on-
board computer. Use a Micro-A – Micro-B USB charging
cable (available from your Bosch eBike dealer) to connect
the USB port on the external device to the USB port (6) on
the on-board computer.
Once the electrical load has been disconnected, the USB
port must be carefully resealed with the protective
cover (17).
USB connections are not waterproof. When cycling in the
rain, do not connect any external devices and make sure
that the USB port is fully sealed by the protective
cover (17).
Important: If electrical loads are connected, this can affect
the range of the eBike.
1 270 020 XBK | (12.03.2019)