Focus Setting; Operation Without Dmx Controller; Activating / Deactivating The Music Control Adjusting The Microphone Sensitivity; Selecting A Show Program - IMG STAGELINE TWIST-52LED Bedienungsanleitung

4.4 Focus setting

For operation with a DMX light controller, make the
focus setting via DMX channel 14 (in 15-channel
mode) or via channel 13 (in 16-channel mode)
[ chapter 9.2]. For operation without DMX con-
troller, make the focus setting via the control but-
tons (4). In this case, the focus settings for gobo
wheel 1 and gobo wheel 2 are made separately:
1) Press the button MENU repeatedly until the dis-
play (5) shows Focus1 Adjust.
2) Press the button ENTER. The head goes to a
vertical position and gobo 1 of gobo wheel 1
appears. The display shows the value adjusted
(0 – 255).
3) Press the buttons
4) To memorize, press the button ENTER.
5) Press the button MENU so that the display
shows Focus2 Adjust.
6) Press the button ENTER. Gobo 1 of gobo wheel
2 appears.
7) Repeat the focus setting for gobo wheel 2.
8) To exit the setting mode, keep the button MENU
pressed until the moving head starts the operat-
ing mode adjusted or wait for one minute and do
not press any button.

5 Operation without DMX controller

If no DMX control signal is present at the jack DMX
INPUT (9), the yellow indicating LED MASTER (3)
lights up, the display (5) shows the number of the
show program adjusted (Show 1 – 4) and the unit
automatically runs through the show program.
Important: Deactivate the blackout mode for this
purpose, chapter 4.3.
5.1 Activating / deactivating
the music control,
Adjusting the microphone sensitivity
Activate or deactivate the music control to define if
the movements of the light beam and the change of
light patterns and colours are music-controlled via
the microphone (2) or not:
1) Press the button MENU (4) repeatedly until the
display shows Sound State.
2) Press the button ENTER. The display starts
flashing.
3) Press the button
deactivate (Off) the music control.
4) To memorize, press the button ENTER. The dis-
play shows Sound State.
Downloaded from www.Manualslib.com
and to focus the gobo.
or to activate (On) or
manuals search engine
5) To exit the setting mode, keep the button MENU
pressed until the moving head starts the show
program or wait for one minute and do not press
any button.
The green LED SOUND (6) briefly lights up
when the light colour, the light pattern or the
movement of the light beam changes due to a
music signal.
6) For music control, set the microphone sensitivity
in such a way that the movements of the light
beam and the change of light patterns and
colours reproduce the dynamic power of the
music in an optimum way. To change the sensi-
tivity, press the button MENU repeatedly until
the display shows Sound Sense.
7) Press the button ENTER. The value adjusted
(0 – 100) starts flashing.
8) Press the button or
the sensitivity.
9) To memorize, press the button ENTER. The dis-
play shows Sound Sense. To exit the setting
mode, keep the button MENU pressed until the
moving head starts the show program or wait for
one minute and do not press any button.
Notes
1. When you change the volume of the music system,
adapt the microphone sensitivity accordingly.
2. If the volume is too low or if the microphone sensitivity is
too low, the moving head will automatically change the
light pattern, the colour of the light beam and the move-
ment of the head.

5.2 Selecting a show program

Four different show programs are available which
differ in the maximum pan and tilt angles of the
head:
Show 1 is provided for setting up the moving head
on the floor. The maximum tilt angle is 210°.
Show 2 is provided for ceiling installation. The
maximum tilt angle is 90°.
Show 3 is provided for setting up the moving head
on stage towards the audience. The pan angle is
160° and the tilt angle is 90° (60° above the hor-
izontal plane and 30° below the horizontal
plane).
Show 4 is also provided for ceiling installation. The
maximum pan angle is 160° and the maximum
tilt angle is 90° (75° to the front and 15° to the
rear).
1) To select Show 1 – 4, press the button MENU (4)
repeatedly until the display shows Show Mode.
2) Press the button ENTER. The display starts
flashing.
to decrease or increase
GB
19