Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
vided on the lower side of the moving head, then
GB
turn them clockwise to the stop. Screw the clamp,
together with the moving head, to the crossbar.
WARNING Install the light effect unit safely and
4.2 Power supply
WARNING To prevent damage to your eyes,
Connect the mains cable provided to a mains jack
(14), then connect it to a socket (230 V~ / 50 Hz). The
head (8) and all control motors go to their starting
positions. The display (5) meanwhile shows LED-
MS50 to indicate that the moving head is ready for
operation. It is either operated via a DMX light con-
troller (
the control program adjusted (
switch off, disconnect the mains plug from the
socket.
For a more convenient operation, it is recom-
mended to connect the moving head to a mains
socket which is switched on and off via a light switch.
4.3 Basic settings
To make the following basic settings via a menu
(
chapter 9.1), use the buttons MENU,
ENTER (4). Press the button MENU repeatedly
until the display (5) shows the desired function.
Then press the button ENTER.
Note: If you do not press any button for one minute, the
moving head will stop the setting procedure and return to
the normal operating mode.
Split Light patterns in two colours
Color
Press the button
No
Light patterns (gobos) in one colour: The
colour wheel latches at a single colour.
18
Downloaded from
www.Manualslib.com
expertly. If it is installed at a place
where people may walk or sit under
it, additionally secure it (e. g. by a
safety rope: Fasten the safety rope
via the threaded eye bolt provided in
such a way that the maximum falling
distance of the unit will not exceed
20 cm. Screw the eye bolt into the
corresponding threaded jack on the
lower side of the unit).
never look directly into the light
source for a long time.
Please note that fast changes in light-
ing, e. g. flashing light, may trigger
epileptic seizures with photosensitive
persons or persons with epilepsy!
chapter 6) or automatically runs through
or
to select:
manuals search engine
Yes Light patterns in two colours: Positions
between two colours are possible.
To memorize, press the button ENTER.
Black Blackout mode on or off
Out
Press the button
The light beam is always activated. Select
No
this setting when operating the moving head
without DMX controller.
Yes The light beam is only activated when a DMX
control signal is present at the jack DMX
INPUT (9). Once the DMX controller has
been switched off, the light beam is deacti-
vated.
To memorize, press the button ENTER.
Pan
Inverse or opposite
For operation with two TWIST-52LED moving
heads, the arm of one unit may pan in one direction
while the arm of the second unit pans precisely in
the opposite direction.
Press the button
No
pan direction normal
Yes pan direction opposite
To memorize, press the button ENTER.
Tilt
Inverse or opposite
For operation with two TWIST-52LED moving
chapter 5). To
heads, the head of one unit may tilt in one direction
while the head of the second unit precisely tilts in
the opposite direction.
Press the button
No
tilt direction normal
Yes tilt direction opposite
To memorize, press the button ENTER.
,
and
Back
Light
Press the button
Yes The display backlight is always on.
The display backlight is switched off approxi-
No
mately 60 seconds after you press the last
button. It is switched on again when you
press the next button.
To exit the setting mode, keep the button MENU
pressed until the moving head starts the operating
mode adjusted or wait for one minute and do not
press any button.
or
to select:
Pan direction normal
or
to select:
Tilt direction normal
or
to select:
Display backlight
or
to select:
Werbung
Kapitel
Inhaltsverzeichnis
