Applications; Installation; Setting The Spotlight Into Operation - IMG STAGELINE PARL-74RGBW Bedienungsanleitung

G
Do not place any vessel filled with liquid on the
unit, e. g. a drinking glass.
G
The heat generated inside the unit must be dissi-
pated by air circulation; never cover the air vents
of the housing.
G
Do not operate the unit or immediately discon-
nect the mains plug from the socket
1. if the unit or the mains cable is visibly dam-
aged,
2. if a defect might have occurred after the unit
was dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the unit must be repaired by skilled
personnel.
G
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the unit and no liability
for any resulting personal damage or material
damage will be accepted if the unit is used for
other purposes than originally intended, if it is not
safely installed or not correctly connected or
operated, or if it is not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
3

Applications

This LED spotlight is used for illumination, e. g. on
stage, in clubs and ballrooms. As a light source,
five extra bright 8 W RGBW LEDs are used. Com-
pared to incandescence lamps, they feature a low
power consumption, a low heat generation and a
long life. The LEDs are able to emit coloured light
in the three primary colours (red, green and blue)
and white light, but also light created by additive
colour mixing. Crossfading from one colour to
another and stroboscope effects are also possible.
The unit is designed for control via a DMX light
controller (3, 4, 5, 6 or 8 DMX control channels
available), but it is also possible to operate it on its
own or in combination with several PARL-74RGBW
spotlights (master / slave mode). In addition, the
integrated microphone provides effects in sync with
the music.
4

Installation

When placing the unit, always ensure a sufficient
air circulation during operation. Never cover the air
vents of the housing.
WARNING Install the spotlight safely and
expertly. When installing it at a place
where people may walk or sit under
it, additionally secure it (e. g. via a
safety rope on the mounting bracket;
fasten the safety rope in such a way
that the maximum falling distance of
the unit will not exceed 20 cm).
1. Fasten the spotlight via a mounting bracket (7),
e. g. with a stable mounting screw or a support
for lighting units (C-hook) on a crossbar.
To adjust the spotlight, release the two lock-
ing screws (3) on the mounting bracket, adjust
the desired inclination of the spotlight, then
retighten the screws.
2. Alternatively, place the spotlight as desired. Use
the mounting brackets as a stand; position them
under the spotlight so that they will support it.
Then fasten the locking screws.
5

Setting the Spotlight into Operation

WARNING To prevent damage to your eyes,
never look directly into the light
source for a long time.
Please note that fast changes in
lighting, e. g. flashing light, may trig-
ger epileptic seizures with photosen-
sitive persons or persons with
epilepsy!
Connect the mains cable provided to the mains
jack (5) first, then connect it to a socket (230 V/
50 Hz). Thus, the spotlight is ready for operation.
Operate it via a DMX light controller (
or on its own using the automatic control program
adjusted (chapter 7). To switch off, disconnect the
mains plug from the socket.
For a more convenient operation, it is recom-
mended to connect the unit to a mains socket
which is switched on and off via a light switch.
Caution: Never connect the unit to the mains volt-
age via a dimmer!
The unit is protected against overheating; it will
automatically switch off when the temperature is
too high and switch on again after cooling down.
chapter 8)
13