Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this
tool, or before performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air hoses and fittings. Do not abuse hoses or connectors.
•
Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged label.
•
Do not use the tool if the trigger does not turn the tool on or off.
•
Do not lock, tape or wire the «on/off» safety lever in the «on» position, as the lever must be free to return to the «off» position
when released.
•
Be sure all hoses and fittings are the correct size and are tightly secured.
•
The use of a hose whip is recommended. A coupler connected directly to the air inlet increases tool bulk and decreases tool
maneuverability.
•
For maximum performance, the coupler on the wall should be the next size larger than the coupler used on the tool. The coupler
closest to the tool should not be less than the proper air supply hose size.
•
Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or
against the body is unstable and can lead to loss of control.
•
When not in use, disconnect tool from air supply to prevent accidental or unauthorized use in the absence of the operator.
•
Do not alter any part/component/accessory of this tool in any way.
•
Mesh air strainer at air inlet occasionally becomes clogged with debris, blocking air supply, and decreasing the tool's
performance. If this occurs the mesh air strainer needs to to be cleaned.
•
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of untrained users.
•
Place the tool on the work surface before starting the tool. Do not point or indulge in any horseplay with this tool.
•
When cutting off, the workpiece shall be supported such that the slot is kept at constant or increasing width during the complete
operation.
•
If the bit becomes jammed in a cut slot, shut off the hammer and ease the bit free. Check that the bit is still correctly secured and
not damaged before continuing the operation.
2 - SERVICE
•
Tool service must be performed by qualified repair personnel, using only FACOM authorized, identical replacement parts. Use
only lubricants recommended by FACOM.
3 - ADDITIONAL SPECIFIC SAFETY RULES FOR AIR HAMMERS
WARNING
•
lnspect the bit before use. Do not use bits which (possibly) have been dropped or which are chipped, cracked or otherwise
defective.
•
Ensure that the bit is correctly mounted and tightened before use and run the hammer at no-load speed for at least 1 min in a
safe position; stop immediately if considerable vibration or other defects are detected and determine the cause of these defects.
•
When chipping or scaling in potentially explosive environment, use spark resistant chisels (usually made of
beryllium copper).Consult the tool manufacturer before using tool in this manner.
•
Use only chisels, scalers or other attachments suitable for use with impacting tools.
•
Do not use tool without chisel retainer being properly secured to tool.
•
Chisels that are worn or blunt at the cutting edge or shank should not be used as such conditions promote tool breakage, reduce
efficiency and increase vibration. A chisel which breaks can cause injury by creating unexpected movement.
•
Do not store chisels at 32°F (0°C) or lower temperatures. Freezing temperatures can make hardened steels brittle, which can
cause breakage and lead to injury.
•
Do not run tool unless steel/chisel/needles are in contact with the working surface. Running tool without steel/chisel/needles in
contact with working surface can damage tool and chisel retainer.
•
The tool's power is controlled by the pressure exerted on the trigger, firmly grip the tool and squeeze the trigger to operate.
PROPER HAND POSITION
Warning: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.
Warning: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires holding the air hammer, with both hands
NU-V.330FH-V.335FH_0317.indd 10
WARNING
10
15/03/2017 09:38:44
Werbung
Inhaltsverzeichnis
