Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
LED fl ash light
Item no. 75 41 71 (red)
Item no. 75 41 72 (green)
Item no. 75 41 73 (orange)
Item no. 75 41 74 (blue)
Intended use
The LED fl ash light is intended to produce short fl ashes of light at regular intervals (approx.
8 or approx. 25 fl ashes per second depending on the type of connection) when connected to a
power source (12 - 24 V/DC). With this function, the LED fl ash light can be used e.g. for signal-
ling alarms, light effects in nightclubs or to indicate operating conditions.
The product may be installed and used outdoors and indoors (IP65).
Any other use than that described above may damage the product. Moreover, this may give
rise to hazards such as short-circuiting, fi re, electric shock, etc. No part of the product may be
modifi ed or converted!
The safety instructions must be observed at all times!
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• LED fl ash light
• Operating Instructions
Explanation of the Symbols
This symbol indicates specifi c risks associated with handling, function and use.
☞
The "Hand" symbol indicates special tips and operating information.
Safety Instructions
Please read all the instructions before using this device, they include impor-
tant information on its correct operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modifi cation of the product is not allowed for
safety and approval reasons (CE).
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical loads.
• The product is not a toy and should be kept out of the reach of children!
• Do not use this product in rooms or under adverse ambient conditions where com-
bustible gases, vapours or dust are or may be present! There is a risk of explosion!
• To avoid eye injury, do not look at the light source or point the light at persons or
animals.
• Fast, regular fl ashes of light may lead to epileptic seizures in certain people. This
is also possible in people who have never experienced an epileptic seizure before.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• In commercial institutions, the accident prevention regulations of the employer's
liability insurance association for electrical systems and operating facilities are to
be observed!
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Installation
www.conrad.com
• The LED fl ash light can produce light fl ashes at two different frequencies; either approx. 8 or
25 fl ashes per second are produced depending on the type of connection:
Version 02/12
Flash frequency approx. 8 fl ashes/sec.
Black cable
Red cable
Flash frequency approx. 25 fl ashes/sec.
Black cable
Yellow cable
☞
• Depending on the surface, the LED fl ash light must be secured with two suitable screws, and
wall plugs if necessary. However, before this, a suffi ciently large opening for the connection
cable is needed.
Protect the connecting cables from a short-circuiting. When installing the product outdoors,
make sure that moisture cannot penetrate the cable connections (e.g. screw connections,
terminals).
• Switch on the mains voltage and make sure that the LED fl ash light is functioning.
Maintenance and Care
• The product does not require maintenance. The LED bulb is permanently installed and can-
not be replaced.
• The exterior of the LED fl ash light should only be wiped with a clean, soft, dry cloth. Do not
use aggressive cleaning agents or chemical solutions that could damage the housing (discol-
ouring) or impair operation.
Do not press too hard on the housing, as scratches might appear.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Disposal
Technical Data
Operating voltage ................ 12 - 24 V/DC
Power consumption .............. 120 mA
Light source .......................... LED, not replaceable
Protection type ...................... IP65
Flash frequency .................... approx. 8 or approx. 25 fl ashes per second (depending on con-
Cable length ......................... approx. 160 mm
Dimensions ........................... 110 x 38 x 35 mm (L x W x H)
Weight .................................. 53 g
GND/minus (-)
Plus (+): 12 - 24 V/DC
GND/minus (-)
Plus (+): 12 - 24 V/DC
If you only need one fl ash frequency, insulate the unused cable e.g. with a shrink
tubing.
Depending on the desired function, it is possible to toggle between the fl ash fre-
quencies (e.g. using an external switch, or similar.).
When drilling holes or screwing into place, ensure that no existing electrical cables,
gas or water pipes will be damaged.
Dispose of the unserviceable product according to the relevant statutory regulations!
nection type)
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
Werbung
