AEG IDE74243IB Montage- Und Gebrauchsanweisung Seite 79

The Automatic Heat UP function allows the set power to be reached
more quickly; with this function it is possible to cook food faster
without the risk of burning it, insofar as the temperature does not
exceed the set level.
This function is available for power levels 1-8 .
Activation:
• from the cooking zone on press
• a flashing " " is shown in the Display (2) which alternates with the
power set in the cooking zone
Increasing the power level of the cooking zone: the Automatic Heat
Up function remains active, with the new temperature setting;
Decreasing the power level of the cooking zone: the Automatic Heat
function is deactivated.
Note: by selecting another cooking zone at the same time, the
symbol (7) will return to being illuminated with a slight intensity
light, and it will be possible to proceed, also for this area, to activation
of the function; the function remains active in the area where it has
already been set, as indicated in the Display (2)
Warming Function
Warming Function is a control function that allows the maintaining of
heat at a constant temperature, at an optimised power level; ideal to
keep ready-cooked foods warm. The Warming Function is activated
the first time the key is pressed
The symbol appears in the display (2) of the zone that is
working in the Warming Function
Note: by selecting another cooking zone at the same time, the
symbol (8) will return to being illuminated with a slight intensity
light, and it will be possible to proceed, also for this area, to activation
of the function; the function remains active in the area where it has
already been set, as indicated in the Display (2)
• Press (8) again to deactivate and switch off , until
bringing of the level shown in the Display (2) to "
Note: if there are several zones working in the Warming Function,
first select the desired zone using the Selection zone (2) ;
the function can also be deactivated via the Selection Bar (3),
bringing the Power Level to "
Pause
The Pause function allows active functions on the cooktop to be
suspended, bringing the cooking power to zero.
Activation:
• press " " (9)
• a flashing " " is shown in the displays (2)
To deactivate the function:
• press (9) the Selection Bar (3) lights up
• press/slide on the Selection Bar (3) to deactivate the function
(7)
".
".
Note: deactivation restores the conditions of the hob before the
pause; the hob continues to work with the same settings previously
set.
Note: if after 10 minutes thePause Function is not deactivated, the
hob switches off automatically.
Note: the Pause Function does not affect the extraction.
"STAND ALONE" Timer
The Timer function is a countdown independent of the cooking zones
(and the extraction zone).
The timer is activated by pressing the Zone/Display (4)
Use the symbols
Timer,which is displayed in the Zone/Display (4)
Note: wait 10 seconds without pressing any other command,
so that the countdown starts.
The format of the Timer is .
- . for the times
- for the minutes
Note: the timer can be set up to a maximum of 1h and 59min.
In the Zone/Display (4) the remaining time will be displayed;
at the end of the countdown, an acoustic signal will sound
Note: in the display of the countdown, for a time less than 10
minutes, the following format is evident
- . minutes
- seconds
with fixed light point
To switch off the Timer:
• select Zone/Display (4)
• set the duration of the Timer to
Note: If timer is ON and the appliance is switched OFF, the timer
remain ON until it expires.
To reset the timer before, switch ON the appliance again, the timer
will switch OFF.
Cooking Zones Timer
The Cooking Timer Zone function is a countdown that can be set,
also at the same time, on each cooking zone
At the end of the period set, the cooking zones switch off
automatically and the user is notified with a dedicated acoustic signal.
Activation of the cooking zone timer function
• Touch (press) the Selection/Display area (2) (power level ≠0)
• Press (6) relating to the cooking zone
Use the symbols
which is displayed in the Zone/Display (4)
during setting the symbol
Note: wait 10 seconds without pressing any other command, so that
the Cooking Zone Timer will start.
Note: by pressing and holding
reset
If desired, repeat the operation for several cooking zones.
Note : each cooking zone can have a separate Timer set; the
countdown for the selected cooking zone will be appear on the
display (4);
79
(5) to set the duration of the
, via (5)
(5) to set the duration of the Timer,
(6) is flashing
(6) , the cooking zone timer is