Safety Information; Technical Data; Unpacking; Attachment - Scheppach Trike S Original Bedienungsanleitung

5. Safety information

• Take suitable measures to prevent children from
accessing the appliance.
• Immediately replace any faulty components.
• We are not liable for any damage caused as a re-
sult of any unauthorised repair and unauthorised
handling or use contrary to the use as designated.
m Warning: Sweeping of any gel, liquid, combustible,
explosive, hot and unhealthy substances prohibited.
m Attention! If metal, glass or sharp objects have
been swept, it is necessary to use firm working gloves
when emptying the dirt collecting container.

6. Technical data

Dimensions LxWxH (mm)
Drive
Max. working width with
side brushes (mm)
ca. Sweeping capacity
(m²/h)
Container content (l)
Weight (kg)

7. Unpacking

• After unpacking, check all parts for any transport
damage. Inform the supplier immediately of any
faults. Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself
with the machine by carefully reading these in-
structions.
• Use only original scheppach accessories, wearing
or replacement parts. You can find replacement
parts at your scheppach dealer.
• When ordering, include our item number and the
type and year of construction of the machine.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There i s a risk of
swallowing and suffocation!

8. Attachment

About packaging used requires your machine is not
completely assembled.
First, remove the accessories from the collection
container and examine it for completeness. (Fig. 3)
• Mount the feeder brushes to the intended axis and
fasten it with 3 screws (b). (Fig. 4)
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
593 x 650 x 1000
manual
650
2000
22
5,56
• Attach the lower part of the push handle to the des-
ignated assembly points with the clamping thumb-
screw on both sides. Fig. 5
• Attach the upper part of the push handle (2) as
shown in Figure 6.

9. Operation

When the sweeper is moved, the feeder brushes
(7) and sweeping brushes (9) start rotating, helped
by the belt drive. Rotating feeder brushes (7) drive
the dirt to the centre. It is then collected by sweeping
brush and taken to the dirt collecting container (5).
Emptying the dirt collecting container
If you want to take out the dirt collecting container to
empty it, take it by its handle and pull up.

10. Maintenance

Use a wet cloth for plastic parts cleaning. Do not use
any cleaning agents, solvents or sharp objects.
After every use - Remove the appliance off dust and
dirt.
If the brush is not rotating it can be that the storage of
the brushes is dirty or the belt isn´t good. Clean and
lubricate the bearing of the brush or replace the belt
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Brushes, drive belts, wheels
* Not necessarily included in the scope of delivery!

11. Storage

For any longer storage the appliance must be thor-
oughly cleaned and stored so as unauthorised per-
sons could not access it.
• Empty the dirt collecting container
• Adjust the brushes to relieve them
• Store the appliance when it is dry
To save spaces, the sliding handle can be folded.
Loosen the screws, pull the sliding handle out and
fold forward.

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
GB | 11