Landxcape LX835 Benutzerhandbuch Seite 21

The charging time is far more than the
rated charging time.
The mower does not charge.
TM
Landxcape is starting to have shorter
run-times between charges.
TM
Landxcape is not operating at the
correct time.
TM
Landxcape cannot correctly dock
with the charging station.
The green light on the charging station
turns on before charging is complete.
TM
Landxcape runs outside the boundary
wire.
TM
Landxcape does not mow an area
within a boundary wire zone.
TM
Landxcape reverses or rotates
erratically near the boundary wire.
TM
Landxcape wheels skid or damage
lawn.
TM
Landxcape exits the boundary wire
due to high speed when going down a
hill.
TM
Landxcape runs in circles; turns right
or left even there is no obstacle in front
of it.
EN
Poor connection caused by debris on the
charging strip.
The charging protection program has activated
due to high temperature.
There is no power.
TM
Landxcape does not operate correctly while
manually charging.
Something is clogging in the blade disc.
TM
Landxcape is shaking heavily.
The battery may be exhausted or old.
The clock is not set to the correct time.
Programmed cutting times for Landxcape
are not correct.
TM
Landxcape is manually docked in the
charging station.
The battery does not charge as its temperature
O
rises above 55 C in hot weather.
Environmental influences.
Poor connection caused by debris on the
charging strip.
The charging station is overheated.
The boundary wire has been installed with
tight corners.
The cutting area is larger than the allowable
TM
cutting area for Landxcape .
The boundary wire of another Landxcape
or another robotic mower is positioned too
closely.
In wet conditions, the boundary wire electric
signal may leak were wire has been joined or
repaired.
There is boundary wire electric signal leakage
due to broken insulation.
Foreign obstacles, such as twigs and branches
TM
may be lodged under Landxcape
The lawn is too wet.
The boundary wire is placed on a slope
steeper than 17% (10°).
Software update failure occurs.
The boundary wire of another Landxcape
or another robotic mower is positioned too
closely.
Clean the contact pins located on the charging station
and the charging strip on Landxcape
Place the charging station in a shady area or wait
until the temperature has cooled down.
Check the power cord is connected properly to the
charger and the charger is connected to a suitable
power supply.
Refer to manual charging in Section 7.3.
Take off the blade disc and clean it.
Check the blade disc and blades, remove debris and
foreign objects from the blades and blade disc.
Replace battery.
Set the clock to the correct time, refer to Section 4.3.
TM
Change the time settings for the mower to start and
stop.
Press then
Wait until the battery has cooled down.
TM
Restart Landxcape
Clean the contact pins located on the charging station
and the charging strip on Landxcape
Place the charging station in a shady area or wait
until the temperature has cooled down.
Check the boundary wire to ensure the corners are
smooth.
Reduce the cutting area or use Landxcape
larger allowable cutting area.
TM
Ensure your Landxcape
1m of space between the neighboring boundary wire.
Check boundary wire joints. Insulate to provide a fully
waterproof connection.
Repair damaged boundary wire insulation with
connectors.
Remove foreign objects from underside of
TM
. Landxcape .
Wait until lawn has dried.
Reposition the boundary wire away from slopes that
are steeper than 17% (10°). Please refer Installation
Guide for details.
Try again according to section "Software update".
check and ensure your Landxcape
TM
has at least 1m of spacing between the neighboring
boundary wire. If the problem cannot be solved,
please contact Landxcape
TM
using a cloth.
.
.
TM
using a cloth.
TM
with a
TM
boundary wire has at least
boundary wire
TM
service agent for help.
TM
21