Landxcape LX835 Benutzerhandbuch Seite 14

4. Understanding Your Landxcape
Congratulations on your new purchase of Landxcape
to the care-free life of automatic mowing. In the following, we want to
help you to better understand how your Landxcape
4.1 How does my Landxcape
to mow?
TM
Landxcape chooses its direction at random. It will make sure your
entire lawn is evenly mowed without leaving unattractive mowing paths
(See Fig. A).
4.2 How does my Landxcape
where to go?
TM
Your Landxcape is made to work on its own. Landxcape
when it needs to go to its charging station to charge, can sense when
it is raining, can stop itself if it senses a problem, and knows to stop,
draw back, and turn around when it bumps into something blocking
TM
its path. Landxcape will also automatically stop its blade turning disc
from rotating if it is lifted off the ground to prevent an accident.
A. Finding the Charging station
TM
When your Landxcape needs to recharge, it will stop mowing and
follow the boundary wire in an anti-clockwise direction back to its
charging station.
B. Rain sensors
TM
Landxcape is equipped with a rain sensor which detects rain and tells
TM
Landxcape to stop mowing and follow the boundary wire back to its
charging station (See Fig. B).
TM
Landxcape will resume mowing after passing the delay time. The
default delay time is 180mins.
When the rain sensors are wet, Landxcape
base. When the rain sensors are dry, Landxcape
time countdown. If you want to exit from the rain delay, dry the sensor
area, and perform a power cycle by operating the on/off key. After the
power cycle has been performed, you can operate again.
C. Sensing the boundary wire
TM
Landxcape always obeys the border set by the boundary wire and
uses sensors at its front to detect it. (See Fig. C)
D. Starting and stopping while mowing (See Fig. D, E1, E2)
To start mowing, press the on/off key and input the PIN code. Press
, then press . If you would like Landxcape
press the STOP button on top of the mower.
TM
If Landxcape senses something is wrong, it will display a fault message
on the display. For information on these messages, refer to "9.Error
14
TM
TM
and welcome
TM
thinks.
TM
know what
TM
know
TM
knows
TM
returns to its charging
TM
will begin the delay
TM
to stop mowing, simply
TM
Messages". Landxcape will turn off if it does not receive any input from
the user within 20 minutes.
To resume:
• Press , then press
TM
• Now Landxcape will begin to mow!
4.3 Setting
Before starting your Landxcape TM
the grass to the height 6 cm or lower with your ordinary lawn mower
or trimmer .Then, set the cutting height of your Landxcape
maximum setting (6 cm) for its first time mowing. And you can do the
program setting manually by rotating the knob.
NOTE: When doing the program setting manually, Landxcape
enter the standby page if it does not receive any input from the user
within several seconds.
Only for reference
As the picture shown above ,you can clockwise and anti-
clockwiserotate the knob.
Please be attention to the arrow on the right of the knob which points
to the function you have chosen.
(1)Change PIN code
To change the PIN code, keep pressing both
time for 5 seconds. The icon will be blinking, and "
be rolling flashing. After that, the first number will be blinking, use
to input the old PIN code and press
blinking. Use the same method to complete other numbers. Then,"
will be rolling flashing , the first number will be blinking and use
select the number you want and press
be blinking. Use the same method to complete other numbers. For example,
the new PIN code is set to be 0326. After that, "
flashing and the first number will be blinking again. Use the same method to
input the new PIN code you set just now (in this example,
" will be rolling flashing on the display. Your PIN code has
been changed successfully.
Only for reference
for the first time, you should cut
to its
TM
will
TM
and buttons at the same
" will
or
to confirm. The next number will be
or
to confirm. The next number will
" will be rolling
). Then "
EN
"
to