Functional Description; Operation; Maintenance; Optional Accessories - Makita GD0600 Betriebsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch lever actuates properly and returns to the
"OFF" position when released.
• Do not pull the switch lever forcibly without pushing in
the lock-off lever.
For tool with lock button
To prevent the switch lever from accidentally pulled, a
lock-off lever is provided. To start the tool, pull the lock-off
lever toward the operator and then pull the switch lever.
Release the switch lever to stop. For continuous
operation, pull the switch lever and then push in the lock
button. To stop the tool from the locked position, pull the
switch lever fully, then release it.
For tool without lock button
To prevent the switch lever from accidentally pulled, a
lock-off lever is provided. To start the tool, pull the lock-off
lever toward the operator and then pull the switch lever.
Release the switch lever to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing wheel point
Loosen the collet nut and insert the wheel point into the
collet nut. Use one wrench to hold the spindle and the
other one to tighten the collet nut securely. (Fig. 2)
The wheel point should not be mounted more than 8 mm
from the collet nut. Exceeding this distance could cause
vibration or a broken shaft. (Fig. 3)
To remove the wheel point, follow the installation
procedure in reverse.
CAUTION:
• Use the correct size collet cone for the wheel point
which you intend to use.

OPERATION

Turn the tool on without the wheel point making any
contact with the workpiece and wait until the wheel point
attains full speed. Then apply the wheel point to the
workpiece gently. To obtain a good finish, move the tool in
the leftward direction slowly. (Fig. 4)
CAUTION:
• Apply light pressure on the tool. Excessive pressure on
the tool will only cause a poor finish and overloading of
the motor.
Downloaded from www.Manualslib.com manuals search engine

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Wheel points
• Collet cone set (3 mm, 6 mm, 1/4", 1/8")
• Wrench 13
• Vise holder
• Side handle set
Side handle (Fig. 5)
When using the side handle, remove the rubber protector,
insert the side handle on the tool barrel as far as it will go
and rotate it to the desired angle. Then tighten the handle
firmly by turning clockwise.
CAUTION:
• When using the tool without handle, always install the
rubber protector on the tool.
• When installing the rubber protector, always push it
onto the tool until the protrusion inside the rubber fits to
the grooves in the tool.
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: surface grinding
Vibration emission (a
h,SG
Uncertainty (K): 1.5 m/s
ENG104-1
): 74 dB (A)
pA
ENG206-3
2
): 2.5 m/s or less
2
ENG902-1
5