Bosch Texoro Originalbetriebsanleitung Seite 15

Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Grinding spindle
(2) Dust extraction guard
(3) Extraction outlet
(4) Clamping screw for mounting dust extraction
guard
(5) Handle (insulated gripping surface)
(6) On/off switch
(7) Speed preselection thumbwheel
(8) Flexible wheel
(9) Flap wheels
(10) Shank for sanding sleeve
a)
(11) Sanding sleeve
(12) SDS mount
(13) SDS mounting spring
(14) SDS actuator button for unlocking the abrasive
tool
(15) Tool arm
(16) Fastening groove of the dust extraction guard
(17) Latching grooves
a)
(18) Extraction hose
(19) Dust extraction adapter (dia. 19 mm)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Sanding roller
Article number
Speed preselection
Rated power input
No-load speed n
0
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 79 dB(A); sound power level
90 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
Sanding with sanding sleeve: a = 3.5 m/s
h
Bosch Power Tools
Sanding with flap wheel (60 mm): a
K = 1.5 m/s
Sanding with flap wheel (10 mm): a
Working with wire brush: a
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
a)
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
a)
u
Changing the abrasive tools
You can use the SDS mount (12) on the grinding spindle (1)
to easily and conveniently change the abrasive tool without
Texoro
using additional tools.
The Autolock system locks the grinding spindle when the
3 603 CB5 1..
power tool is switched off. It is better to attach or remove
●
abrasive tools when the grinding spindle is fixed in place.
W 250
Flexible rollers (8), flap wheels (9) and wire brushes can be
-1
min 1600−3000
attached directly to the grinding spindle (1).
For sanding sleeves (11), the shank (10) must first be at-
kg 1.3
tached to the grinding spindle (1). The sanding sleeve (11)
can then be twisted onto the shank (10).
/II
Fitting the abrasive tools (see figure A)
– Hold the abrasive tool so that the SDS mounting
– Slide the abrasive tool onto the grinding spindle (1) in a
– Check that it is locked by pulling on the abrasive tool.
Fitting the sanding sleeves (see figure B1 − B2)
– Hold the shank (10) so that the SDS mounting
– Slide the shank (10) onto the grinding spindle (1) in a
2 2
, K = 1.5 m/s ,
2
,
= 6 m/s
h
Pull the plug out of the socket before carrying out any
work on the power tool.
springs (13) are pointing away from the grinding
spindle (1).
turning motion until you hear it engage.
springs (13) are pointing away from the grinding
spindle (1).
turning motion until you hear it engage.
1 609 92A 66Y | (13.01.2021)
English | 15
2
= 2.5 m/s ,
h
2 2
= 3 m/s , K = 1.5 m/s ,
h
2 2
, K = 1.5 m/s .