Other Symbols In This Documentation; Information On The Appliance; Units Of Measurement; Safety - STIEBEL ELTRON ISG WEB Bedienung Und Installation

OPERatIOn

Safety

1.3

other symbols in this documentation

Note
General information is identified by the symbol shown
on the left.
f Read these texts carefully. f
Symbol Meaning
Material losses
!
(Appliance and consequential losses, environmental pol-
lution)
Appliance disposal
f This symbol indicates that you have to do something. The ac- f
tion you need to take is described step by step.
1.4

information on the appliance

Symbol Meaning
Never cover the appliance
1.5

units of measurement

Note
All measurements are given in mm unless stated oth-
erwise.
2. safety
2.1

intended use

This appliance is used for monitoring and remote control of your
ventilation unit or heat pump.
This appliance is designed for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-do-
mestic environment, e.g. in a small business, as long as it is used
in the same way.
Any other use beyond that described shall be deemed inappropri-
ate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
2.2

appliance compatibility

Note
The date of manufacture of the system is crucial for de-
termining appliance compatibility.
If the date of manufacture does not meet the minimum
requirements listed below, your system is not suitable
for operation with the appliance.
www.stiebel-eltron.com
Note
Do not connect the appliance to a system with a controller
that does not have the minimum software versions listed
below installed.
f If necessary, let customer support install the re- f
quired controller versions in your system.
The appliance can be operated in conjunction with the following
ventilation units and heat pumps:
System type date of manu-
facture
LWZ
LWZ 303 (Integral)
LWZ 303 SOL
LWZ 403 SOL
LWZ 304 SOL
LWZ 404 SOL
WPF/WPC with WPMiw
WPC 5/7/10/13
WPC 5/7/10/13 cool
WPF 5/7/10/13/16 cool E
WPF 5/7/10/13/ 16 cool
WPF 5/7/10/13/ 16 basic
WPL/WPF with WPM II
WPL 10 I/A/IK
WPL 13/18/23 E
WPL 13/18/23 cool
WPL 13/20 A basic
WPL 13 B IK
WPL 34/47/57
WPF 10/13/16 M
WPW M
WPF 20/23/26/29/32 Set
WPF 20/27/35/40/52/66
WPF 27 HT
WPL with WPM 2.1
WPL 33 HT
WPL 15 AS
WPL 25 A
WPL with WPM me
WPL 15 IKS-2 / IS-2
WPL 25 IK-2 / I-2
WPF/WPC with WPM3i
WPC 04/05/07/10/13
WPC 04/05/07/10/13 cool
WPF 04/05/07/10/13/16
WPF 04/05/07/10/13/16 cool
Note
Any installed remote control FEK must have at least soft-
ware version 9506 or higher installed.
Note
Do not operate the appliance with a DCO active GSM on
the same CAN BUS. This can impair communication with
the WPM.
Minimum controller
software version
from 08/2008 no restriction
from 08/2008 no restriction
from 08/2008 no restriction
no restriction no restriction
no restriction no restriction
from 01/2009
from 01/2009
from 01/2009
from 01/2009
from 01/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
from 05/2009
no restriction no restriction
no restriction no restriction
no restriction no restriction
no restriction
no restriction
no restriction no restriction
no restriction no restriction
no restriction no restriction
no restriction no restriction
ISG WEB |
32508
32508
32508
32508
32508
6529
6529
6529
6529
6529
6529
6529
6529
6529
6529
6529
34007
34007
17