Operation - Makita BHP343 Bedienungsanleitung

using this ring.
For rotation only, turn the ring so that the arrow on the
tool body points toward the
For rotation with hammering, turn the ring so that the
arrow points toward the
For rotation with clutch, turn the ring so that the arrow
points toward the
CAUTION:
Always set the ring correctly to your desired mode
•
mark. If you operate the tool with the ring
positioned halfway between the mode marks, the
tool may be damaged.
Adjusting the fastening torque
Fig.6
The fastening torque can be adjusted in 16 steps by
turning the adjusting ring so that its graduations are
aligned with the arrow on the tool body. The fastening
torque is minimum when the number 1 is aligned with
the arrow, and maximum when the number 16 is aligned
with the arrow.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing driver bit or drill bit
Fig.7
Turn the sleeve counterclockwise to open the chuck
jaws. Place the bit in the chuck as far as it will go. Turn
the sleeve clockwise to tighten the chuck.
To remove the bit, turn the sleeve counterclockwise.

OPERATION

Hammer drilling operation
CAUTION:
There is a tremendous and sudden twisting force
•
exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips
reinforcing rods embedded in the concrete.
First, turn the action mode changing ring so that the
arrow on the tool body points to the
adjusting ring can be aligned in any torque levels for this
operation.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Downloaded from www.Manualslib.com
mark on the ring.
mark on the ring.
mark on the ring.
and particles, or when striking
marking. The
manuals search engine
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Blow-out bulb (optional accessory)
Fig.8
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Screwdriving operation
Fig.9
First, turn the action mode changing ring so that the
arrow on the tool body points to the
the adjusting ring to the proper torque level for your work.
Then proceed as follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
CAUTION:
Make sure that the driver bit is inserted straight in
•
the screw head, or the screw and/or bit may be
damaged.
NOTE:
When driving wood screws, predrill pilot holes to
•
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
006421
Drilling operation
First, turn the adjusting ring so that the pointer points to
the marking. Then proceed as follows.
CAUTION:
Pressing excessively on the tool will not speed up
•
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
There is a tremendous force exerted on the tool/bit
•
at the time of hole break through. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
A stuck bit can be removed simply by setting the
•
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
6
marking. Adjust
Recommended size of pilot hole
(mm)
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
4.0 - 4.2
4.2 - 4.4