Setting The Temperature - Bosch sensixx B25L TDS25 Serie Gebrauchsanleitung

en
11. Mains cable with storage facility
12. Cord clip
13. Temperature dial
14. Iron pilot light
15. Iron´s steam release button
16. Soleplate
* Model dependent
Preparations (A)
1. Remove any label or protective covering from the
soleplate.
2. Place the appliance horizontally on a solid, stable
surface. You may remove the iron pad from the
appliance and place the iron on it on another solid,
stable, horizontal surface.
3. Remove the detachable water tank (1) and fill it,
making sure not to pass the level mark.
4. Fit the water tank back onto the steam tank.
5. Unwind the mains cable (11) fully and plug it into an
earthed socket.
6. Set the main power button (6) to the "I" position.
7. The "Steam ready" indicator lamp (7) will light up after
several minutes, indicating that the appliance is ready
to use.
The steam generator will take more time to reach
"Steam ready" state only upon the initial heating up,
or after performing the de-scaling operation (Calc'n
clean).
When water is already present in the steam generator
during regular use, heat up time to reach the operating
temperature will be faster.
8. This appliance has a built-in water level sensor. The
"refill water tank" indicator (8) will light when the water
tank is empty.
Important:
• Normal tap water can be used.
To prolong the optimum steam function, mix tap water
with distilled water 1:1. If the tap water in your district
is very hard, mix tap water with distilled water 1:2.
You can inquire about the water hardness with your
local water supplier.
• The water tank can be filled at any time while using the
appliance.
• To avoid damage and/or contamination of the water
tank and the boiler, do not put perfume, vinegar,
starch, descaling agents, additives or any other type
of chemical product into the water tank.
Any damage caused
aforementioned products, will make the guarantee
void.
12
All manuals and user guides at all-guides.com
• The iron is not designed to rest on its heal. Please
• The iron pad can be placed into the specially designed
• During it first use the iron may produce certain vapours
• While the steam release button is pressed, the water

Setting the temperature

1. Check the ironing instruction label on the garment to
2. Select the temperature (13)
3. The indicator lamp (14) will remain lit while the iron is
Tips:
• Sort your garments out based on their cleaning
• If you are not sure what the garment is made of then
Ironing with steam (B)
1. Turn the temperature selector (13) to the required
2. Set the amount of steam to suit your needs, using the
3. Press the steam release button to release steam.
Attention:
1. When ironing on a lower temperature setting "•".
by the use of the
• If the appliance has variable steam control (3), set the
always position it horizontally on the iron pad (2).
recess on the appliance or somewhere suitable along-
side the ironing area.
Never rest the iron on the appliance without the
iron pad!.
and odours, along with white particles on the soleplate,
this is normal and it will stop after a few minutes
tank may produce a pumping sound, this is normal,
indicating that water is being pumped to the steam tank.
determine the correct ironing temperature.
"•" Synthetics
"••" Silk – Wool
"•••" Cotton – Linen
heating and go out as soon as the iron has reached
the selected temperature.
symbol labels, always starting with clothes that have
to be ironed at the lowest temperatures.
begin ironing at a low temperature and decide on the
correct temperature by ironing a small section not
usually seen when worn
setting.
variable steam control (3) (depending on the model).
For normal use, please choose one of the following
recommended settings:
Temperature Steam setting
•
••
•••
variable steam control to its lowest position ("1").
1
5
10
V