Functional Description; Operation - Makita 6095D Bedienungsanleitung

4. Charge the Nickel Metal Hydride battery
cartridge when you do not use it for more than
six months.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Fig.1
Always switch off the tool before insertion or
•
removal of the battery cartridge.
To remove the battery cartridge, pull out the set
•
plate on the tool and grasp both sides of the
cartridge while withdrawing it from the tool.
To insert the battery cartridge, align the tongue on
•
the battery cartridge with the groove in the housing
and slip it into place. Snap the set plate back into
place. Be sure to close the set plate fully before
using the tool to prevent the battery cartridge from
accidentally falling out of the tool.
Do not use force when inserting the battery
•
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Switch action
Fig.2
CAUTION:
Before inserting the battery cartridge into the tool,
•
always check to see that the switch trigger
actuates properly and returns to the "OFF" position
when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Reversing switch action
Fig.3
This tool has a reversing switch to change the direction
of rotation. Slide the reversing switch to the right (appear
"F" marking) for clockwise rotation or to the left (appear
"R" marking) for counterclockwise rotation.
CAUTION:
Always check the direction of rotation before
•

operation.

Use the reversing switch only after the tool comes
•
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
Speed change
Fig.4
To change the speed, turn the speed change knob so
that the arrow of the desired speed on the knob is
aligned with the reference arrow on the tool body. If the
speed change knob does not turn easily, switch on the
Downloaded from www.Manualslib.com manuals search engine
tool and turn the knob again while the tool is running
under no load. Be sure that the speed change knob is
set to the correct position before operation. Use the right
speed for your job.
Adjusting the fastening torque
Fig.5
The fastening torque can be adjusted in 6 steps by
turning the adjusting ring so that the pointer on the
adjusting ring points to a number on the tool body. The
fastening torque is minimum when the pointer points to
the number 1 and maximum when it points to
the marking.
The clutch will slip at various torque levels when set at
the number 1 to 5. The clutch is designed not to slip at
the marking.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
NOTE:
The adjusting ring does not lock when the pointer
•
is positioned only halfway between the numbers.
Overload protector
The overload protector automatically cuts out to break
the circuit whenever heavy work is prolonged. Wait 20 -
30 seconds before resuming operation.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing driver bit or drill bit
Fig.6
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck.
To remove the bit, hold the ring and turn the sleeve
counterclockwise.
OPERATION
Screwdriving operation
Fig.7
CAUTION:
Adjust the adjusting ring to the proper torque level
•
for your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
5