Sharp KH-6IX38FS00-EU Bedienungsanleitung Seite 37

be displayed and the hob will switch off.
Key Lock
The key lock function is used to set
'safe mode' on the appliance during
operation. It will not be possible to make
any adjustments by pressing the buttons
(for example heat settings). It will only be
possible to switch the appliance off.
The lock function is active if the key lock
button is pressed for at least 2 seconds.
This operation is acknowledged by a
buzzer. After successful operation, the key
lock indicator will flash and the heater will
be locked.
Timer Function
The timer function is available in two
versions, as follow.
Minute Minder Timer (1 - 99 min.)
The minute minder timer can be operated
if the cooking zones are switched off. The
timer display will show "00" with a blinking
dot.
Use the Timer and Sliding Button
to increase/decrease the time.
The range is between 0 and 99 minutes.
If there is no adjustment to the displayed
time within 10 seconds, the minute minder
timer will be set and the blinking dot will
disappear. Once the timer is set, it begins to
count down.
When the timer reaches zero, a signal will
sound and the timer display will blink. The
sound signal will stop automatically after 2
minutes and/or by pressing any button.
The minute minder timer can be changed or
switched off any time by using the Timer
and Sliding Button
the hob by touching
switch off the minute minder timer.
Cooking Zone Timer (1 - 99 min.)
When the hob is switched on, an
independent timer can be programmed for
each cooking zone.
Select a cooking zone, then select the
temperature setting and, finally, activate the
timer setting button
programmed to switch off a cooking zone.
Four LEDs are arranged around the timer
that indicate which cooking zone the timer
has been set for.
10 seconds after the last operation, the
timer display will change to the timer that
will run out next (in cases where a timer is
set for more than one cooking zone).
When the timer has run down, a signal will
. Switching off
at any time will also
, the timer can be
EN - 16
sound, the timer display will show "00" and
the assigned cooking zone timer LED will
blink. The programmed cooking zone will
switch off and "H" will be displayed if the
cooking zone is hot.
The sound signal and the blinking of the
timer LED will stop automatically after 2
minutes and/or by pressing any button.
Buzzer
While the hob is in operation, the following
activities will be signalled by the buzzer.
• Normal button activation will be
accompanied with a short sound signal.
• Continuous button operation over a
longer period of time (10 seconds)
will be accompanied with a longer,
intermittent sound signal.
Boost Function
To use this function, select a cooking zone
and set the desired cooking level, then
press the "P" (Boost) button.
The Boost function can only be activated
if it is applicable with the cooking zone
selected. If the Boost Function is active,
a "P" will be shown on the corresponding
display.
Activating the booster can exceed the
maximum power, in which case the
integrated power management will be
activated.
The necessary power reduction is shown
by the corresponding cooking zone display
blinking. Blinking will be active for 3
seconds to allow for further adaptations of
the settings before power reduction.
Bridge Zone
Switching the Bridge Zone On
Touch the front left and rear left heater
selection buttons simultaneously. A static
dot will be shown on the left heater display.
Displays will show 'b' and 'r', alSo, touCh
the front riGht anD rear riGht heater
SeleCtion key SiMultaneouSly. there
iS a StatiC Dot inDiCation on the riGht
heaterS DiSplayS anD DiSplayS Will
ShoW the 'b' anD 'r'. The blinking dots will
no longer be displayed.
Select the temperature setting by using the
sliding button. Increase the heat setting by
pressing the right side of the sliding button
or decrease the heat setting by pressing the
left side of the sliding button.
The bridge element will be ready to use.
For the fastest boil time, select the desired