Environmental Information - Husqvarna ROYAL 53S Betriebsanleitung

G3-a - Recoil Starter
G5-a - Drive Speed Control
G5-b - Engine Speed Control
Starting & Stopping Royal 53S, 53S Intek.
Starting
1. Connect the spark plug lead.
2. Move the Engine Speed Control to the FAST '+'
position before starting. (G1)
3. Pull the operator presence control (OPC) to release
the brake on the engine and the blade.(G2)
4. Pull the recoil starter fully towards you until you feel
the full resistance, return the handle slowly then pull
the handle firmly towards you to its full extent. (G3)
5. After the engine has started, allow to run for 30
seconds before commencing to use.
Engaging the Drive
1. Forward drive is engaged and disengaged with the
Powerdrive lever at the top of the handle (G4).
2. Drive speed can be altered with the drive speed
control. (G5)
How to Mow
1. Always use the correct mowing position (J1).
2. Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions (J2).
3. Mow twice a week in the growing season, your lawn
will suffer if more that one third of its length is cut at
one time and this may also result in poor collection.
Cutting Height Adjustment
1. The height of cut is altered by pulling the adjustment
lever away from the location slots and moving to the
selected position (J3).
IMPORTANT: Do not attempt any maintenance on your
lawnmower when the engine is hot.
IMPORTANT: Never use water for cleaning your
lawnmower. Do not clean with chemical, including petrol,
or solvents - some can destroy critical plastic parts.
Cleaning
1. Remove grass from under the deck with a brush (K1
and K2).
2. Using a soft brush - remove grass clippings from the
engine air intakes and exhaust (K3), cutting height
adjustment area. (K4), around the wheels (K5) and
the grassbox (K6).
3. Wipe over the surface of your lawnmower with a dry cloth.
Cutting System (L)
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Renew your
metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of condition. If
the blade is cracked or damaged replace it with a
new one.
Removing the Blade
• Disconnect the spark plug lead.
1. Use spanner to loosen blade bolt by turning anti-
clockwise.
2. Remove the blade bolt, blade and spacer washer.
Electrolux Outdoor Products are manufactured under an
Environmental Management System (ISO 14001)
using, where practical, components manufactured in the
most environmentally responsible manner, according to
company procedures, and with the potential for
recycling at the end of the products' life.
ENGLISH - 3
Downloaded from www.Manualslib.com
Use - Starting and Stopping

Environmental Information

manuals search engine
3. Releasing the Powerdrive Lever stops the forward
drive automatically.
Stopping
1. Release the powerdrive lever.
2. Release the OPC lever.
Starting & Stopping Royal 53SE
Starting
1. Follow steps 1-3 for the Royal 53S
2. Turn the key and hold until the engine starts (H). The key
will return to the original position when released.
3. If the engine fails to start when you turn the key
your battery may need charging.
Please note:- Your Royal 53SE can be started
manually by following steps 1-5 in
Starting & Stopping Royal 53S, 53S Intek
Key Start Only - During mowing, your engine will
recharge the battery
Engaging the Drive - See Royal 53S, 53S Intek
Stopping - See Royal 53S, 53S Intek
Use - Mowing
Emptying the Grassbox
1. Lift the safety flap (J4).
2. Remove the grassbox from the machine (J5)
3. Empty grassbox.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height, will help reduce engine overload and
will help prevent damage to your lawnmower.
Maintenance
3. Inspect for damage and clean as necessary.
Fitting the Blade
1. Fit the blade to the machine with the sharp edges
pointing away from the machine.
2. Re-assemble blade bolt through blade and spacer
washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
How to Charge the Battery (53SE ONLY)
M1 - Battery Loom
M2 - Battery Charger
M3 - Wiring Loom
1. Stop your lawnmower.
2. Disconnect the spark plug.
3. Disconnect the wiring loom from the battery loom
(M).
4. Plug charger lead into connection on battery loom
5. Plug the battery charger into a domestic electric
socket.
6. Charging will then commence.
7. Charge for 24 hours.
8. After charging, disconnect the charger from the
socket and charging point.
9. Connect the wiring loom to the battery loom (M)
10. The unit is now ready for use.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.