Inhaltsverzeichnis
Werbung
CONNECTION TO A
Plasma Display
1.
Switch off the power of the plasma display.
2.
Connect the input terminals of the speaker
system and the speaker output terminals
of the plasma display with the accessory
speaker cable.
The polarity of the input terminals is plus (+) for the red
terminal (the terminal on the right side in the following figure)
and minus (-) for the black terminal (the terminal on the left
side in the following figure).
1.Remove the insulation and twist the core ends together.
2.Push the lever, insert the cable into the hole, and release the
lever.
Minus terminal
Minus terminal
Speaker output terminals of the plasma display.
• After connection to the terminals, pull lightly on the cable to
confirm that the tips of the cable are connected positively to
the terminals. An imperfect connection can cause sound
interruptions and noise.
• When cable cores stick out and + and - lines are short-
circuited, an excessive load will be applied to the plasma
display and the operation will stop or trouble will be caused.
48
Ge
Downloaded from
www.Manualslib.com
Ofrecido por www.electromanuales.com
Plus terminal
Plus terminal
manuals search engine
Installation to commercial
mounting fittings
Washer M8
(ø 25)
MAINTENANCE
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• When the cabinet is very dirty, wipe with a soft cloth
moistened with water-diluted cleanser; then wipe again with
a dry cloth. Do not use furniture wax or cleaners. They may
damage the surface of the cabinet.
• Never use thinner, benzine, insecticide sprays and other
chemicals on or near the cabinets, since these will corrode
the surfaces.
• When a chemical cloth is used, read the cautions for the
chemical cloth carefully.
SPECIFICATIONS
Cabinet: Enclosed type
Used speakers (two-way method) :
Woofer (for low tones) . . . . . . . . . . . . . . . . . . . Oval cone type
Tweeter (for high tones) . . . . . . . . . . . . . . . . 2.5 cm dome type
Nominal impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Ω
Frequency Range . . . . . . . . . . . . . . . . . . . . . . 50 to 20,000 Hz
Sensitivity . . . . . . . . . . . . . . . . . . . . 82 dB/W (at 1 m distance)
Permissible input :
Max. input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 W
Rated input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 W
Crossover frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 kHz
External Dimensions . . . . . . . . 74 (W) x 714 (H) x 101 (D) mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 kg
Accessory parts (for 2 speakers) . . . . . . . . . . . . . . . . . . . . . . ..
Speaker cable x 2, Flat countersunk head screw x 4, Hexagon
socket head screw x 4, Mounting tool x 1, Washer M8 (ø 25) x
2, Speaker mounting fittings (for top left side) x 1, Speaker
mounting fittings (for top right side) x 1, Speaker mounting
fittings (for bottom) x 2, Mounting plate (for left side) x 1,
Mounting plate (for right side) x 1, User Manual x 1
Specifications and design subject to possible modification
without notice, due to improvements.
This unit includes M8 (ø 25)
washers for installation on
commercial mounting fittings.
Installation is made by two-
point fixing at the top side
mounting holes for
commercial mounting fittings.
As these two mounting holes
are not at the same level,
washers are used to
compensate for this
difference.
Werbung
Inhaltsverzeichnis
