Concept CP3000 Bedienungsanleitung Seite 30

EN
Steam Mop Operation
1. Attach the mop pad to the holder.
2. To attach the mop pad holder: place the front of the steam
cleaner on the holder, align the foot pedal to the centre
of the head and gently press the head to the holder until
it "snaps" together.
NOTE: Never use the steam mop without the microfiber
steam mop pad in place.
3. For carpet cleaning only, proceed according to step
3 and fit the carpet glider on the head. If the steam
cleaner is used on hard floors, remove the carpet
glider.
4. Grasp the water tank release lever and pull forward
and upward to remove the water tank.
5. Remove the cap from the bottom of the water tank and
fill it with water. Make sure the cap sealing is in its place.
Screw the cap and put the water tank back.
NOTE: Do not attempt to use steam mop with an
empty water tank!
6. Turn the power switch on, (the power indicator will be on).
7. Press the steam level button, to adjust the steam level.
The default is maximum, can be adjusted to minimum.
8. When the MIN/MAX indicator stops flashing (when it
light steadily), press and hold the steam trigger (on the
inner side of the handle) to start steam cleaning.
9. When the Steam Mop stops emitting steam turn the
power OFF and refill the water tank.
10. Steam Settings:
Tiles/Stone - Maximum
Sealed wooden floor - Minimum
NOTE: When the microfiber steam mop pad becomes too
wet or dirty, replace with a clean cloth.
The microfibre cover is machine washable at 40 °C.
58
CP 3000
EN
VAC
VAC
Steam Steam
Steam
trigger
CP3000
47
EN
EN
USE & MAINTENANCE
USE & MAINTENANCE
Maintenance
Maintenance
1. When finished steam cleaning, ensure to turn off the appliance and unplug from the mains.
1. When finished steam cleaning, ensure to turn off the appliance and unplug from the mains.
2. Empty the remaining water from the water tank.
2. Empty the remaining water from the water tank.
3. Remove the mop pad. Microfibre pads can be washed in a washing machine, up to 100 °C. For heavily
3. Remove the mop pad. Microfibre pads can be washed in a washing machine, up to 100 °C. For heavily
soiled pads, soak them in warm water with detergent or a mild stain remover beforehand. Allow the pads
soiled pads, soak them in warm water with detergent or a mild stain remover beforehand. Allow the pads
to dry completely before storing. NOTE: DO NOT USE FABRIC SOFTENER
to dry completely before storing. NOTE: DO NOT USE FABRIC SOFTENER
Changing the Water Filter
Replacing the water filter
Changing the Water Filter
The water filter will help filter minerals that reduce the effectiveness of the steam cleaner. Depending on
The water filter helps to filter minerals contained in water that reduce the efficiency of the steam cleaner. The water filter will help filter minerals that reduce the effectiveness of the steam cleaner. Depending on
water conditions and use frequency, the filter should be replaced every 80-100 hours.
Depending on the frequency of use of the appliance, the filter should be replaced every 80-100 hours. Use water conditions and use frequency, the filter should be replaced every 80-100 hours.
The steam mop will work using ordinary tap water. However, if you live in an area with hard water, the minerals
The steam mop will work using ordinary tap water. However, if you live in an area with hard water, the minerals only distilled water in the steam mop. If you live in an area with hard water, this water may cause deposits on
that form the hard water will reduce the life of the water filter installed in the steam mop. This will eventually
the heater, which will reduce the performance of the cleaner. Use only distilled water. This will extend the that form the hard water will reduce the life of the water filter installed in the steam mop. This will eventually
allow deposits to build up on the heat element of the appliance, which will reduce its performance. To prolong
service life of the water filter and heater.
allow deposits to build up on the heat element of the appliance, which will reduce its performance. To prolong
the life of your filter and heater, we recommend using distilled or de-mineralized water.
the life of your filter and heater, we recommend using distilled or de-mineralized water.
WARNING: Unplug the cord from the mains before maintenance.
WARNING: Unplug the cord from the mains before maintenance.
Outlet Filter Maintenance
Outlet Filter Maintenance
Push the filter cover tab down and remove it from the appliance body.
Push the filter cover tab down and remove it from the appliance body.
Remove the filter from the back of the cover and wash it until it is
Remove the filter from the back of the cover and wash it until it is
completely clean. Before returning the filter, allow it to dry thoroughly.
completely clean. Before returning the filter, allow it to dry thoroughly.
Put the filter cover back into the appliance - align the bottom of the
Put the filter cover back into the appliance - align the bottom of the
cover with the appliance body and rotate it to its place. It snaps when it
cover with the appliance body and rotate it to its place. It snaps when it
is in the right place.
is in the right place.
Dirt tanks
Dirt tanks
Remove the filter unit from the dirt tank. Turn the coarse outer filter
Remove the filter unit from the dirt tank. Turn the coarse outer filter
counterclockwise and release it. Turn the main filter counterclockwise and
counterclockwise and release it. Turn the main filter counterclockwise and
release it. Remove the outer foam filter from the bottom of the main filter.
release it. Remove the outer foam filter from the bottom of the main filter.
Clean all the filters and let them dry properly before assembly. Place the
Clean all the filters and let them dry properly before assembly. Place the
foam filter on the bottom of the main filter. Put the main filter back into
foam filter on the bottom of the main filter. Put the main filter back into
the case. Turn the main filter clockwise until it locks into place. Place the
the case. Turn the main filter clockwise until it locks into place. Place the
foam filter on the bottom of the main filter. Put the main filter back into
foam filter on the bottom of the main filter. Put the main filter back into
the case. Turn the main filter clockwise until it locks into place. Place the
the case. Turn the main filter clockwise until it locks into place. Place the
coarse outer filter on the main filter and align the unlock symbol with the
coarse outer filter on the main filter and align the unlock symbol with the
arrow symbol on the coarse filter. Turn the coarse outer filter clockwise
arrow symbol on the coarse filter. Turn the coarse outer filter clockwise
until it snaps and locks into place. Return the filter unit back to the dirt
until it snaps and locks into place. Return the filter unit back to the dirt
tank. Place the dirt container back into the appliance body.
tank. Place the dirt container back into the appliance body.
48
CP3000
48
EN
CP 3000
59
CP 3000