Specifications - Makita LB1200F Betriebsanleitung

ENGLISH (Original instructions)
1. Wheel
2. Upper cover
3. Light switch
4. Switch
5. Rip fence
6. Lower cover
7. Carry Handle
8. Dust box
9. Knob (For tensioning blade)
10. Knob (C)
11. Knob (D)
12. Knob (For adjusting blade guide)
13. Knob (For securing blade guide)
14. Upper blade guide
15. Blade
16. Knob (For tensioning V-belt)
17. Driving belt
18. Stand
19. Tire
20. Lock lever (For securing table tilt)
21. Dust extraction port
22. (Quick release) lever
23. Knob (For adjusting cutter tool tracking)
24. Grip (For adjusting table tilt)
25. Frame
26. Handle
27. Washer
28. Hex socket head bolt

SPECIFICATIONS

Model
Wheel size
Max. cutting capacity
No load speed
Cutting speed
Blade size
Overall dimensions
Table size
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the tool. Be sure that you
understand their meaning before use.
.......... Read instruction manual.
.......... Withdraw the main plug.
.......... Wear safety glasses.
.......... Do not place hand or fingers close to the blade.
.......... Only for EU countries
Do not dispose of electric equipment together with
household waste material!
Explanation of general view
29. Plate spring
30. Securing hole
31. Position hole
32. Table
33. Hex bolts
34. Trunnion
35. Pin
36. Thumb screw
37. Guide rail
38. Switch cover
39. OFF switch
40. ON switch
41. ON
42. Push stick
43. Miter gauge
44. Lock handle
45. Knob
46. Knob (A)
47. Fence
48. Lock lever
49. Fence holder
50. Knob (B)
51. Hold-down clamp
52. Thumb screws
53. Dust cover
54. Saw blade
55. Saw housing
56. Lower blade guard
High
Low
High
Low
Circumference 2,240 mm x Width 6 mm, 13 mm, 16 mm
END215-2
Intended use
The tool is intended for cutting in wood or nonferrous metal using
appropriate saw blade.
Power supply
The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated
on single-phase AC supply. This tool should be grounded while in
use to protect the operator from electric shock. Use only three-wire
57. Quick release lever
58. Lower band saw wheel
59. Motor pulley
60. Driving belt
61. Pulley of the driving wheel
62. Approx. 10 mm
63. Lock knob
64. Adjusting knob
65. Guide bearing
66. Bolt A
67. Guide bearing distance from bottom of
blade
68. Bolt C
69. Bolt B
70. Bearing holder
71. Thrust bearing
72. Screw
73. Nut
74. Large opening collector
75. Small opening collector
76. Small dust collector (Mounted on main
unit)
77. Large dust collector (For changeover)
78. Rail
79. Shoulder
80. Hex bolt
LB1200F
305 mm
165 mm
840 min -1 (50 Hz)/1,040 min
420 min -1 (50 Hz)/520 min
13.3 m/s (800 m/min) (50 Hz)/16.7 m/s (1,000 m/min) (60 Hz)
6.7 m/s (400 m/min) (50 Hz)/8.3 m/s (500 m/min) (60 Hz)
615 mm x 775 mm x 1,600 mm
560 mm x 400 mm
81.2 kg
In observance of the European Directive, on Waste
Electric and Electronic Equipment and its
implementation in accordance with national law,
electric equipment that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
-1 (60 Hz)
-1 (60 Hz)
ENF001-1
11