Operation - Makita HR2800 Bedienungsanleitung

Bit angle (when chipping, scaling or
demolishing)
For models HR2810, HR2810T, HR2811F, HR2811FT
Fig.14
The bit can be secured at the desired angle. To change
the bit angle, rotate the action mode changing knob to
the O symbol. Turn the bit to the desired angle.
Rotate the action mode changing knob to the
Then make sure that the bit is securely held in place by
turning it slightly.
Fig.15
Depth gauge
Fig.16
The depth gauge is convenient for drilling holes of
uniform depth. Loosen the side grip and insert the depth
gauge into the hole in the side grip. Adjust the depth
gauge to the desired depth and tighten the side grip.
NOTE:
The depth gauge cannot be used at the position
•
where the depth gauge strikes against the gear
housing.
Dust cup
Fig.17
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Dust cup 5
Dust cup 9
006406

OPERATION

CAUTION:
Always use the side grip (auxiliary handle) and
•
firmly hold the tool by both side grip and switch
handle during operations.
Hammer drilling operation
Fig.18
Set the action mode changing knob to the
Position the bit at the desired location for the hole, then
pull the switch trigger.
Do not force the tool. Light pressure gives best results.
Keep the tool in position and prevent it from slipping
away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
symbol.
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm
symbol.
8
Autogoods "130"
CAUTION:
There is a tremendous and sudden twisting force
•
exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with
chips and particles, or when striking reinforcing
rods embedded in the concrete. Always use the
side grip (auxiliary handle) and firmly hold the tool
by both side grip and switch handle during
operations. Failure to do so may result in the loss
of control of the tool and potentially severe injury.
NOTE:
Eccentricity in the bit rotation may occur while operating
the tool with no load. The tool automatically centers
itself during operation. This does not affect the drilling
precision.
Blow-out bulb (optional accessory)
Fig.19
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Chipping/Scaling/Demolition
For models HR2810, HR2810T, HR2811F, HR2811FT
only
Fig.20
Set the action mode changing knob to the
Hold the tool firmly with both hands. Turn the tool on
and apply slight pressure on the tool so that the tool will
not bounce around, uncontrolled. Pressing very hard on
the tool will not increase the efficiency.
Drilling in wood or metal
Fig.21
Fig.22
Fig.23
Fig.24
For Model HR2800, HR2810, HR2810F
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page.
Set the action mode changing knob so that the pointer
points to the symbol.
For model HR2810T, HR2811FT
Use the quick change drill chuck as standard equipment.
When installing it, refer to "changing the quick change
chuck for SDS-plus " described on the previous page.
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck. To remove the bit, hold
the ring and turn the sleeve counterclockwise.
Set the action mode changing knob to the
You can drill up to 13 mm diameter in metal and up to
32 mm diameter in wood.
symbol.
symbol.