Seav LR 2035 Compact Serie Handbuch Seite 6

I
MPORTANT FOR THE INSTALLER
The control unit was designed to be assembled together with
other components (motor, shutter or gate, safety devices) to
constitute a finished product (machine) in compliance with
Machinery Directives.
The safety of the final installation and the compliance with all
prescribed Standards is the responsibility of the person who
assembles the various parts to construct a total closing.
It is also advised to comply with the following
recommendations:
− Before automating the frame, check that it is in good
conditions, in compliance with the Machinery Directive
and with EN 12604.
− Wiring of the various electrical components outside of the
control unit must be carried out in compliance with that
prescribed in Standard EN 60204-1 and its amendments
at point 5.2.7 of EN 12453. Power supply and connection
cables must be fixed using the cable glands supplied as
optional accessories.
− The gearmotor used to move the frame must comply with
that prescribed at point 5.2.7 of EN 12453.
− Fix the control unit on a wall. To mount it, use the special
support supplied with the casing and insert fixing screws
in the designated spaces.
−
The controller must be placed within an environment that
ensures an IP44 degree or higher.
For the fixing of the device, insert the screws through the
slots in the bracket which is supplied with the casing.
−
To facilitate the wiring of the control unit, break the little
pitches of plastic support and, after having made the wire
connections, replace the housing cover.
− Mounting of a push button panel for manual control must
be done positioning the push button panel where the user
is not in a dangerous position, in compliance with point
5.2.8 of EN 12453.
− The control unit does not have any type of isolating device
for the 230 Vac line. It will therefore be the responsibility
of the installer to arrange an isolating device inside the
plant. It is necessary to install a mono-phase switch with
over-voltage category III. It must be positioned where it
can be protected from accidental closing, according to
that prescribed in point 5.2.9 of EN 12453.
− In compliance with 5.4.2 of EN 12453, it is recommended
to use gearmotors equipped with an electric-mechanical
release device, so that the door can be moved manually
in case of necessity.
− In compliance with 5.4.3. of EN 12453, use electric-
mechanical release systems or similar devices which
stop the door safely in the end run position.
− Cables for power and connection to the motor suitable for
insertion in the pg9 cable glands provided must have an
outside diameter between 4.5 and 7 mm. The internal
conductors wires must have a nominal section of
2..
0.75mm If a raceway is not used, use H05RR-F cables.
− Fix a warning sign near the place of installation, conform
with ISO 3864, with minimum height of 60 mm
− Use safety devices capable of monitoring the status of
their connection to the electrical control unit.
− When installation is complete, carry out all the controls
prescribed by EN 12453 - EN 12445 to be sure that the
closing complies with the provisions.
− For a correct functioning of the radio receiver, if using one
or more control units, the installation at a minimum
distance of at least 3 metres one from the other is
recommended.
I
MPORTANT FOR THE INSTALLER
- The device must never be used by children or persons with
reduced physical-psychological abilities, unless supervised or
trained on the functioning and the use modalities.
- Do not allow children to play with the device and keep the
radiocontrols away from their reach.
- Ensure there is no-one immediately near-by until the door is
not fully open or closed.
- ATTENTION: keep this instruction manual and respect the
important safety prescriptions contained herein. The non
compliance with the prescriptions may cause damages and
serious accidents.
- Frequently examine the plant to detect any signs of damaging.
Do not use the device if a repair intervention is necessary.
Warning
All operations that require the opening of the casing (cables
connection, programming, etc.) must be carried out by expert
personnel during installation. For any further operation which
requires the casing to be re-opened (re-programming, repair or
installation amendments) contact the after-sales assistance.
The products:
Electronic control unit:
LG 2035 Compact - LRS 2035 Compact
LRS 2035 SET Compact – LRH 2035 Compact
comply with the specifications of the RED 2014/53/EU,
EMC 2014/30/EU and LVD 2014/35/EU
Directives.
Rev.3.0 del 13/06/2016