Seav LR 2035 Compact Serie Handbuch Seite 5

stop. If a command that is in the opposite direction to the
current movement is sent during upward or downward
movement, the control unit causes the shutter to change
direction.
Operation using a 3-button radio control (BeFree x3 - X6):
When using the BeFree x3 - x6 radio control, you will obtain the
same type of operation as previously described for the BeFree
x1 version; furthermore, the buttons (-) and (+) at the sides of
the radio control may be used to select the (Up - Stop - Down)
commands for 6 different types of operation.
PROGRAMMING:
SEL button: selects the type of function to be memorised, the
selection is indicated by a flashing LED.
By repeatedly pressing the button it is possible to choose the
desired function. The selection will remain active for 10
seconds indicated by a flashing LED. If no other operations are
executed during this period, the control board will return to its
previous state.
SET button: programs the information relative the type of
function previously selected with the SEL button.
LED Reference LED Off
1) CODE No code
2) LAMP/CORT. Flashing
3) T. MOT. Unlimited timing
4) T. PAUSE. No automatic close
1) CODE: (Radiocontrol programming)
Programming: The transmission code is programmed in the
following manner: press the SEL button, LED CODE starts
flashing. At the same time send the first code selected with the
desired radiocontrol and LED CODE will start flashing quickly,
send the second code to be saved. LED CODE will remain on
and the programming is complete. If the second code is not
sent within 10 seconds the control unit will exit the programming
phase and select the function with only one code of the
radiocontrol. In case all 7 available codes have been
memorised, by repeating the programming operation, all 4
LEDs indicators will start to flash very fast, indicating that further
memorising is not possible.
Programming the transmission code remotely.
This procedure allows to program the transmission code
remotely, without using the SEL button on the unit itself, but
remotely following the operation.
To program a transmission code remotely, proceed as follows:
send the code of a previously saved radiocontrol code
continuously for more than 10 seconds, at the same time the
control unit enters the programming mode as described above.
Enabling the programming of a transmission code
remotely.
The control unit is supplied by the manufacturer with remote
programming of a transmission code not enabled; to enable the
function proceed as follows: connect the control unit to a
230Vac power supply by pressing and holding the SEL button.
All the indicator LEDs will turn on and the programming is
complete. To disable the function enabled previously, repeat
the operation or conduct the RESET procedure.
Deletion
Cancellation of all memorised codes is carried out in the
following manner: press the SEL button and LED CODE will
start to flash. Then press the SET button. The procedure is now
complete and LED CODE will stop flashing.
Rule of the memorisation of the first Radio control:
In the programming of radio controls, the following rule applies:
if the first radio control to be memorised is a rolling code type,
LED On
Code activated
Courtesy Light
Programmed delay
With automatic close
the control unit will then only accept rolling code radio controls,
thus ensuring greater safety against intrusions; if the first radio
to be memorised is a fixed code remote control (12 or 18 bits),
then the control unit will accept both the fixed code and rolling
code radio controls having only the fixed part of rolling codes
controlled ((essentially losing the safety feature of the rolling
system).
WARNING: to restore the control unit to factory default
configurations (without applying the rule of the first radio control
memorisation), it is required to perform a RESET of the control
unit because it will not enough to erase memorised radio
controls.
2) LAMP/CORT. : (Selection of the flashing light or the courtesy
light)
The control unit has a 230 Vac output, for connection to a
flashing light or a courtesy light.
The control unit is supplied by the manufacturer with the
Flashing function enabled. If you wish to enable the courtesy
light, proceed as follows: use the SEL button to navigate to the
LAMP/CORT LED when flashing and then press the SET
button. The LAMP/CORT button will light up permanently.
Repeat the procedure to restore the previous configuration.
Flashing function:
each time that the automation is moving, for the duration of the
motor time. If the Pause time is memorised, the flashing light
will be active even during the Pause.
Functioning of the Courtesy light: The 230 Vac output will be
activated for 3 minutes, each time that an ascent command is
given.
3) T. MOT. (Programming the motor operating time max. 4
minutes)
The control unit is factory supplied with a working time motor
predefined equal to 30 sec.
If a reprogramming of the motor operating time is needed, it
must be carried out through the closed frame in the following
manner: use the SEL button to navigate to the T. MOT LED
when flashing, then continuously press the SET button. The
rolling shutter will start the opening. When you have reached
the required height, release the SET button and at the same
time the motor time storage will be completed and the T. MOT.
LED will remain lit and fixed. If you want an infinite motor time,
use the SEL button to navigate to the T.MOT LED when
flashing and press the SET button for less than 1 second. At the
same time the LED will shut off and the operation will be
completed. It is advisable to memorise a time that is a few
seconds longer after the frame has reached the end.
4) T. PAUSE:
(Automatic closing time programming max. 4 minutes)
The manufacturer furnishes the control unit with an automatic
closure (pause time equal to 15 sec.). If a reprogramming of the
automatic closing time is needed, it must be carried out through
the closed frame in the following manner: use the SEL button to
navigate to the T. PAUSE LED when flashing. Then press and
hold down the SET button for a period equal to the desired
pause interval between closing and opening operations. At
expiration of the desired time release the SET button. At the
same time the memorisation of automatic closing time will be
determined and the T. PAUSE LED will remain lit.
If you do not want automatic closing, take position on the
flashing of the T. PAUSE LED. Then press the SET button for
less than a second. At the same time the LED will shut off and
the operation will be concluded.
RESET:
To reset the default configuration of the control unit, press the
SEL and SET buttons simultaneously; all RED indicator LEDs
will switch on and then off again immediately.
Rev.3.0 del 13/06/2016
The 230 Vac output will be activated