Werbung
Verfügbare Sprachen
Verfügbare Sprachen
IMPORTANT INFORMATION
RF100 XL 3D printer fully-assembled
Item no. 1592461 RF100 XL Plus
Item no. 1592620 RF100 XL
Dear Customer,
thank you for purchasing this product.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than 3D printing, the product may be damaged. In addition, improper use can result in
short circuits, fires, electric shocks or other hazards. Read the important information carefully and store them
in a safe place. Make this product available to third parties only together with the quick-start-guide and this
important information.
Detailed Operating Instructions
Download the detailed operating instructions at www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
General information on the 3D printer
A 3D printer is a highly complex device in which many parameters must be set depending
on the printer, printed object and filament material used.
Additionally, the adhesion of the printed object on the build bed is influenced by printing
temperature, filament material, build bed calibration, shape / size of the printed object
and surface properties of the build bed.
Ambience influences such as drafts, grease on the build bed, etc. also play a role in the
quality and adhesion of the printed object.
For the above reasons, it is not possible to reach high-quality print results at once and
without previous experiments.
Change the adjustable parameters in small steps for the best printing results for your
application.The printing examples enclosed on the SD card provide references, but must
be refined for perfect results depending on the above parameters.
Safety Information
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in the
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General information
• For safety reasons, any unauthorized conversions and/or modifications to the product
deviating from these operating instructions are not permitted. Components may be damaged
and thus impair the function or safety of the device.
• All persons who operate this product, mount, install, assemble it, put it into operation or service
it must be trained and qualified accordingly and must observe these operating instructions.
• The 3D printer is not suitable for persons with physical, sensor or mental limitations or for
inexperienced or uninformed persons.
• This product is not a toy and not suitable for children. Children cannot judge the dangers
involved when handling electrical devices.
• The mechanical parts of the product are produced highly precisely. Never apply any
mechanical force here. The 3D printer may be rendered useless by this.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Attention, LED light: Do not look directly into the LED light! Do not look into the beam directly
or with optical instruments!
• Consult an expert when in doubt about the operation, safety or connection of the appliance.
• Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Set-Up, Site of Operation
• Set up the 3D printer only on a stable, horizontal, sufficiently sized surface.
• Choose the site of operation so that children cannot reach the product.
• When setting up the 3D printer, observe that the mains plug of the mains unit must be easy
to reach so that the device can be separated from the mains voltage quickly and easily in
case of malfunction.
• The devices must not be exposed to any extreme temperatures, strong vibrations, high
moisture, such as rain or steam or strong mechanical strain.
• Never place containers containing liquids, e.g. glasses, vases, etc. on the device or in its
vicinity and do not pour any liquids out over the device. Liquids may get into the housing and
impair electrical safety. This also poses great danger of fire or potentially fatal electric shock!
If this is the case, first power down the respective mains socket on all poles (e.g. switch off
circuit breaker and FI switch) and then pull the mains cable from the socket. Disconnect all
lines from the device. Do not operate any part of the product anymore afterwards, but take it
to a specialist workshop.
• Never place any sources of open fire, such as lit candles, on or right next to the device.
c) Connecting the mains cable
• The only permissible voltage source is a properly grounded mains socket
(100-240 V, 50/60 Hz) of the public mains.
• Connect the appliance to a wall socket that can be accessed easily.
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to the public supply.
Before plugging in the power adaptor, check whether the voltage stated on the power adaptor
complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use
the grips on the plug.
• Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put under
mechanical stress. Avoid excessive thermal stress on the mains cable from extreme heat or
cold. Do not modify the mains cable, otherwise it may be damaged. Damaged mains cables
can cause a fatal electric shock.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
• Do not touch the mains cable if it is damaged. Power down the respective mains socket (e.g.
via the circuit breaker) and then carefully unplug the mains plug from the mains socket. Never
use the product if the mains cable is damaged.
d) Operation
• Never reach into the 3D printer in operation. The mechanically moved parts within the printer
pose a high risk of injury!
• The nozzle (item no. 1592620 and 1592461) and heating plate (item no. 1592461) may
become very hot during use. Never touch these parts during or shortly after use. Allow them
to cool down for approximately 60 minutes.
• Disconnect the device from the mains before maintenance work or modifications (unplug the
mains plug) and let it cool down.
• In operation, there will be noise and, depending on the filament material used, smells. Observe
this when selecting the site of setup and the filament material. Ensure sufficient ventilation or
install an extraction system. Do not inhale arising vapours. When using any other than the
recommended filament material, poisonous vapours or gases may develop.
• Never operate the device unattended.
• Only operate the device in moderate climates, never in tropical climates.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1592461_1592620_V1_1017_02_LS_hs_GB
Werbung
