Additional Functions; Operation - FARFISA INTERCOMS KM8262W Handbuch

Since there are no other programming to
make, this operation will automatically exit
the programming mode.
c) exit the programming mode following the
instructions described in " Exiting the
programming mode ".
General notes
.
- Always hang up the handset at the end of
programming for each videointercom.
- Repeat the programming steps for all video-
intercoms in the installation.
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger art.2273
is installed.
Ring volume adjustment
To adjust the ring level you must adjust the
trimmer R8 on the wall bracket WB8262.

Additional functions

Call floor
When you make a call floor, you will hear a
different tone. The floor call is used to inform
that somebody is ringing at the house door.
The function is active both when the system is
free and busy.
Call Repeat
You can connect the intercoms as illustrated in
the diagram below to sent the videointercom
ring to other locations in the house.

Operation

Call from external station.
When a call is made from the external station,
the videointercom turns on, generates an
acoustic tone and stays on for about 30 seconds.
If the call time has expired and the videointercom
has turned off, press the button "
with the calling external station. Pick up the
handset to start conversation with the external
station for about 90 seconds and press button
" " to open the door.
In case of a call to a user with more than one
videointercom in parallel installed in the
apartment, all the videointercom will ring, but
only the videointercom with internal address
000 will turn on. You can answer from this
videointercom by following the instructions
above. You can answer from the other
videointercom by picking up the handset. This
To make the programming easier and to remind your self the stored codes, please fill in the following table
operation will automatically turn ON this
videointercom and will turn OFF the intercom
that had been turned ON before. Press button
" " if you want to see the caller before answering
and then pick up the handset.
Monitor function and connection with one
or more external stations.
When the installation is in stand-by and no
conversation is in progress, you can monitor
the entrance by pressing button "
If the installation includes more external stations
and button "
can monitor the external stations (max. 4) in
sequence by pressing the same button again
and again.
The videointercom will be turned ON for about
30 seconds. The monitoring will be interrupted
in case of request of monitor service by another
user, call between users or from an external
station. If you pick up the handset during the
monitoring, you will automatically establish a
voice conversation with the external station.
If the videointercom will not turned ON when you
press button "
busy and you will have to wait until it becomes
free again.
Making or receiving a call from another user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user's in the
button " ". To make the call, pick up the handset,
wait for the free tone and press button " ". You
will hear the call tone and the videointercom of
the called user will ring (without turning on) with
a ring different from calls from external stations
or intercom calls from the same apartment. If
the called user answers within 30 seconds, a 90-
second conversation starts, otherwise the
system goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
If you pick up the handset and receive no tone,
the installation is busy and you must wait until it
is free.
Making or receiving an intercom call in your
apartment.
When the installation is in stand-by, you can
make an intercom call to all videointercom in
the same apartment (max. 3) by pressing the
button " " you have programmed with code 000.
To make the intercom call, pick up the handset,
wait for the free tone and press button " ". You
" to reconnect
will hear the call tone and the videointercoms
that are enabled to receive intercom calls
(internal address 001 or 002) will ring (without
turning ON) with a ring tone different from calls
from external stations or other users. The
videointercom will not ring if it is coded with
internal address 003. However, you can pick up
the handset and start a conversation with the
calling user. If the called user answers within 30
seconds, a 90-second conversation starts,
otherwise the system goes back to free.
".
" is programmed correctly, you
", this means the installation is
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
Tone table
Tone of pressure of a button.
indicate the pressure of one of the buttons
during the programming phase.
0 1 2 3
Acknowledge tone.
It is activated to confirm the
correct operation of the door lock release and
during the programming phase to indicate a valid
operation.
0 1 2 3
Tone of system ready.
Activated for 30 seconds
if the system is free
0 1 2 3
Calling tone.
It is activated during a call to another
user or during an intercommunicating call (active
for 30 seconds or until the called user answers).
0 1 2 3
Dissuasion tone.
It is activated when a
nonexistent device is call or when a device is not
available.
0 1 2 3
End conversation tone.
It is activated 10 seconds
before the conversation time ends.
0 1 2 3
Calling table
External call
0 1 2 3
Call from another user (continuous tone)
0 1 2 3
Intercommunicating call (modulated note)
0 1 2 3
Floor Call
0 1 2 3
Note . All the acoustic signalling, with the
exception, of the system ready and calling tone
last after about 2 seconds.
Mi 2334/1
It is activated to
and
4 5
4 5
4 5
4 5
4 5
4 5
4 5
4 5
4 5
4 5
- 6 -