Peruzzo SIENA 668 Montageanleitung Seite 9

ASSEMBLY AND USER INSTRUCTIONS
Whenever this product is used the following information must be
taken into consideration: the bike rack is a safe product if used
correctly, whereas if it is used incorrectly it can cause damages
to you and to anyone driving behind you.
1) Insert the end plugs 32 in the square bearing tubes 25-26 (Fig. A).
2) Insert the end plugs 23 in the bike carrier bars 27 (Fig. A) and in the
31 (Fig. D2).
3) Mount the tyre cradles 21 on the bike carrier bar 27 in the most suita-
screws 22, nuts and washers 53 (Fig. A).
4) Fix the carrier bars 27 to the square bearing tubes 25-26 with the
screws, nuts and washers 54 (Fig. A).
5) Fix the square tube 24 of the light bar 17 to the square bearing tubes
25-26 with the screws, washers and nuts 51 (Fig. A).
6) Mount the rear lights 18 on the light bar 17
washers and nuts 55 (Fig. B) while taking care not to damage the wires.
Thread the 13 pin plug through the central hole of the light bar 17.
7) Fix the number plate frame 19 to the light bar 17 with the screws 56.
8) Fix the light bar assembly 17 to the square tube 24 with the screws 20,
the nuts and the washers 52; make sure you thread the tilt hook 5 into
the slot provided (Fig. C).
- Unscrew and remove the knobs 36 and the washers 57 from both
sides (Fig. D1);
- Carry out the operations 1 and 2 (Fig. D2);
element 33
HOW TO INSTALL THE BIKE RACK ON THE
TOWING HOOK
To mount the bike rack in safety and to avoid damaging the vehicle, you
should request the help of another person.
10) Remove the safety screw 13
11)Unscrew the screw 8 until the hemisphere 14 (Fig. E) is completely
open.
11 with the hemisphere open 14 to the hitch ball
12
58 (Fig. F) .
13) Tighten the screw 8 with the wrench provided 12 until the hemisphere
14 is secured to the hitch ball 58 (the manual force should be equal to at
least 40 Kg.) (Fig. F).
Lastly mount the safety screw 13
IMPORTANT:
(Fig. F) to avoid any accidental openings.
ONLY FOR ART. 668/4
14) Clean the parts of the bodywork that will be in contact with the straps of
attach the strap hooks
the bike carrier,
the straps in the buckles 39
hatch, then insert
(make sure the inlet direction is correct) (Fig. F1).
: Give the straps a good tug to check for tightness. Check the
IMPORTANT
tightness before starting and during the trip.
POSITIONING and FIXING the BIKES ON
THE BIKE RACK
wheels in the tire cradles 21
31
(Fig. H1
Check that the belts are mounted correctly by pulling on them.
16) Repeat the operations in 15 for the second, third and fourth bikes. The
arms 15/16 (Fig. H1), whereas the fourth bike is secured to the third
41 (Fig. H2).
: For safe transportation of the load the bike carrier is
IMPORTANT
supplied with a strap 38
Check that the belt is mounted correctly by pulling on it.
668_SIENA_20/01/2020
31:
31 in the half pipe of the tilt adjustment
57 and the knobs 36 (Fig. D2).
50 (Fig. E).
40
to the edges of the vehicle
31
37 (Fig. G).
31
EN
BIKE RACK INCLINATION
17) To tilt the bike rack hold it up with one hand while you pull the hook
5 with the other (Fig. I/L).To avoid injury or damage, this operation
of tilting the bike rack should be carried out with the help of a third
person. To close the bike rack lift it until the tilt hook 5 engages
securely in the transit position (Fig. M).
ATTENTION – SAFETY REQUIREMENTS
As well as the information described below please observe the
"
Conditions, suggestions and limits for use
- Weight and maximum capacity of "SIENA" bike racks:
* Model 668 (10,85 kg) - 669 (10,65 kg) ---> 2 bikes, max.
capacity 34 kg.
* Model 668/3 (13,56 kg) - 669/3 (13,33 kg) ---> 3 bikes, max.
capacity 51 kg.
* Model 668/4 (15,93 kg.)
- Never exceed the permitted capacity of the towing hook installed. The
combined weight of the bike rack and the load must never exceed the
permitted capacity. Keep the towing hook ball surface clean from dirt
and oil.
- The driver is always responsible for the load he is transporting and
consequently he is also responsible for checking the fastenings both
before starting the trip and at regular intervals during the trip.
permissible rear axle weight.
- Verify compliance with the value D (maximum load bearing capacity)
D for the towball must be at least (760 Kg) 7.6kN; older towballs
often only specify the permissible load on the towball G
50
total permissible load of the towing vehicle G
this case the value D
the vehicle maintenance or registration booklet:
9,81 (G
x
A
x
D =
1000 (G
A +
(D in [kN] / G in [kg] / G
A
- Remove from the transported bikes children's seats, transport
baskets, rain covers or other elements that could get lost or increase
30
the air resistance.
model.
- Bike parts, such as for example the handlebars or pedals, must not be
left in the normal position of use; they must be folded to avoid
dangerous projections.
that the bikes are secured as instructed.
31.
- The bike rack is only suitable for transporting bicycles.
9/33
(Fig.I/L/M)
---> 4 bikes, max. capacity 60 kg.
rather than value D; in
K
G )
K
G )
K
in [kg])
K
Copyright © 2009 Peruzzo Italy - MADE IN ITALY
and the
A