Safety Instructions And Information - Hauff-Technik HSI150 SEGMENTO Montageanleitung

HSI150 SEGMENTO / SEGMENTO Kombikit KKS
Lagerung
HINWEIS!
Beschädigungen durch unsachgemäße Lagerung!
Bei unsachgemäßer Lagerung können Sachschäden in erheblicher Höhe entstehen.
• SEGMENTO vor der Montage vor Beschädigungen, Feuchte und Verunreini-
gungen schützen. Es dürfen nur unbeschädigte Teile montiert werden.
• Die Lagerung des SEGMENTO muss so erfolgen, dass dieser zu keinen
niederen Temperaturen (<5 °C) und höheren Temperaturen (>30 °C) sowie
keiner direkten Sonneneinstrahlung ausgesetzt ist.
Entsorgung
Sofern keine Rücknahme- oder Entsorgungsvereinbarung getroffen wurde, zerleg-
te Bestandteile nach sachgerechter Demontage der Wiederverwertung zuführen:
• Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten.
• Elastomere nach den geltenden Umweltvorschriften entsorgen.
• Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
• Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.

Safety instructions and information

Target group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
• knowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Conditions.
We explicitly draw your attention to the fact that no warranty whatsoever applies
for any subsequent damage occurring as a result of failure to follow the installation
instructions or if our products are used incorrectly or combined with third-party products.
The HSI150 SEGMENTO is the fastest solution for sealing cables and pipes particularly
gently and neatly at up to 0.5 bar (outside pressure). The individual segments can
be installed without any problem. Cables can be replaced or installed at a later date
without opening the entire system.
Safety
This section provides an overview of all the main safety aspects for optimum
protection of personnel and a safe installation process.
A failure to observe the instructions and safety information set out here may result
in significant hazards.
During installation it is imperative to observe the relevant professional association
rules, the VDE provisions, the relevant national safety and accident prevention
regulations and your company's guidelines (work and procedure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to installa-
tion of the cable entries :
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property damage.
• The nationally applicable laying and filling regulations for pipes and cables are
to be observed at all times.
• Seal the underground and cable substructure well prior to laying pipes/cables
so that the latter cannot subside.
NOTE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• Pack the foundations and cable support well before laying the cables/pipes
to prevent the cables/pipes sinking.
• The incorrect laying of cables or ducts and improper filling of the cable
trench causes settlement, which can lead to damage and leaks.
• Do not open the blind cover of the wall insert until just before installing the
cable. Observe the installation instructions for the system cover.
• Cables and pipes should not be supposed to mechanical load.
6
• Any cable entries that are not required may be used as pressure-tight back-
up entries if there is an undamaged Hauff quality seal on the closing cover.
• Do not knock the blind cover in with a hammer or sharp object!
• Open cable entries, which are to be used as back-up entries, or closing cover
which have been opened accidentally, should be fitted with new HSI150 DT
blind covers!
• Do not reuse uninstalled or damaged closing covers!
• Before mounting a system cover in the cable entry, clean the interior of any
dirt and check the sealing surfaces for any damage.
• Before the process of installing the duct begins, the bottom of the trench
must be free from water and the bottom bedding layer must be created by
a professional in accordance with the installation guidelines provided by the
duct manufacturer.
• The outside of the building must be level, dry and clean prior to installation!
Thoroughly remove, smooth and level out any unevenness on the wall
surface in the flange area.
• Core drilling diameter Ø 150 mm.
• Dowels/screws compliant with the ETA-07/021 approval for concrete walls
are included in the scope of delivery.
• For multiple arrangement is a drilling distance or rather axial distance of >
EN
250 mm required.
• No cleaning agents containing solvent may be used. We recommend using
the cable cleaner KRMTX
• For details of other accessories and further information, see www.hauff-technik.
de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property damage.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the relevant
provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport damage.
In the event of transport damage being visible from the outside, proceed as follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or delivery
note provided by the transporter.
Delivery scope
The HSI150 Segmento is supplied with the following:
Accessories:
The SEGMENTO Kombikits KKS is suplied with the following:
Art. Nr.: 5090032060 Rev.: 01/2020-01-22
WARNING!
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable claim period.
1 HSI150 S3 system cover
1 GMS „SEGMENTO" lubricant (Art.No.: 2300310000)
3 segments of your choice (the segments must be ordered separately to
match the cables to be sealed); the following segments are available:
Segment SEG 2x31 incl. blind plug
Segment SEG 3x26 incl. blind plug
Segment SEG 6x21 incl. blind plug
Segment SEG 8x15 incl. blind plug
1 Flange HSI150 DFK
1 Surface seal made of EPDM
4 Dowel and screws with ETA-07/021 approval
4 Sealing ring for fixing elements and installation on wall with bitumen
coating KMB (PMBC)
1 HSI150 S3 system cover
1 GMS „SEGMENTO" lubricant (Art.No.: 2300310000)
3 Segments of your choice; the following segments are available:
Segment SEG 2x31 incl. blind plug