Monacor DN-200 Anleitung Seite 2

DN-200
Order Number 12.0170
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
3-Way Crossover Network
for Speaker Systems
These instructions are intended for
non-professionals with basic knowledge in
DIY speaker building. Please read the in-
structions carefully prior to operation and
keep them for later reference.
1 Applications
This crossover network is specially designed
for setting up a 3-way speaker system with
a power capability of up to 400 W. Its high-
quality design features air core coils and film
capacitors.
2 Important Notes
The crossover network corresponds to all rele-
vant directives of the EU and is therefore marked
with .
•
The crossover network is suitable for indoor
use only. Protect it against dripping water
and splash water, high air humidity and heat
(admissible ambient temperature range:
0 – 40 °C).
•
For cleaning only use a dry, soft brush; never
use water or chemicals.
•
No guarantee claims for the crossover net-
work and no liability for any resulting per-
Input
IN
L 2
L 3
R 2
L1
L 3 L 2
M M
8 Ω M
L 1
3m5
R1
12 Ω
10 W
C 1 C 2 C 3
Bass
B
8 Ω
C 1 + C 2 C 3
10µ /150 V 4µ7/150 V
MKT MKT
ELECTRONICS FOR SPECIALISTS
sonal damage or material damage will be
accepted if the crossover network is used for
other purposes than originally intended, if it
is not correctly connected, if it is overloaded,
or if it is not repaired in an expert way.
If the crossover network is to be put
out of operation definitively, take it to
a local recycling plant for a disposal
which is not harmful to the environ-
ment.
3 Connection
1) Connect the speakers to the crossover net-
work (fig. 1).
B = bass speaker
M = midrange speaker
H = tweeter
The correct polarity of the midrange speak-
ers and tweeters depends on the speakers
used and on their arrangement within the
speaker system. To determine the correct
polarity, make sound checks. With a 3-way
crossover network, the midrange speaker is
usually connected with reverse polarity as
shown in the figures.
2) The pins "IN" serve as a signal input.
DN-200
400W/8 Ω
MAX.
MONACOR INTERNATIONAL
L 1
ZUM FALSCH 36 · 28307 BREMEN
GERMANY
L 4
L1
L 3 L 2
H H B
8 Ω H 8 Ω B
C 4 C 5
10µ 10µ
150 V 150 V
MKT MKT
L 2
0m5
R 2
12 Ω
10 W
L3
Mid
C 6 C 7
L 3
8 Ω
2m6
L2
M
L1
C 6 C 7
3µ9 /150 V 3µ0 /150 V
MKT MKT
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS
L 3
L 3
3
➀
C 8
3µ9
150 V
MKT
L3
100dB
High
L 4
90
8 Ω
0m5
L2
80
H
70
L1
20 Hz
➃
ELECTRONICS FOR SPECIALISTS ELECTRONICS
3.1 Series connection of midrange
speakers and tweeters
For series connection of two 4 Ω midrange
speakers and / or two 4 Ω tweeters, the cross-
over network is provided with four additional
connection pins (two with the lettering +, two
with the lettering –). The correct connection is
shown in fig. 2.
3.2 Connection of speaker L pads
Speaker L-pads (e. g. model series AT-62 ...
from MONACOR) can be used to perfectly
match the volume of the midrange speaker
and / or tweeter to the volume of the bass
speaker. For this, six connection pins with the
lettering L1 ... L3 are provided. The connection
is shown in fig. 3.
4 Specifications
Input power: . . . . . . . . .400 W max.
Output impedance: . . . . .8 Ω
Crossover frequencies: . .700 Hz and 3500 Hz
Slope: . . . . . . . . . . . . . . .12 dB / octave
Dimensions: . . . . . . . . . .243 × 35 × 160 mm
Weight: . . . . . . . . . . . . .1.3 kg
Subject to technical modification.
R 2
L1
L 2 L 3 L 2
M M H
4 Ω M 4 Ω M
R 2
L1
L 2 L 3 L 2
M M H
8 Ω M
2 2
1 3 1
AT-62... 2 AT-62...
3
1
50 100 200 500 1k
50 100 200 500 1k
A-1727.99.02.01.2019
L 4
L1
H B
4 Ω H 4 Ω H 8 Ω B
➁
L 4
L1
H B
8 Ω H 8 Ω B
➂
2k 5k 10k 20k
100dB
W
90
80
70
2k 5k 10k 20k
➄