Before Using This Unit - Sony HDCU5000 Handbuch

SDI I/O 1 to 4 3G/HD/SD SDI I/O
BNC type (4)
3G SDI: SMPTE ST424/425 Level-A/B,
0.8 Vp-p, 75 ohms, 2.970 Gbps/
2.967 Gbps
HD SDI: SMPTE ST292, 0.8 Vp-p,
75 ohms, 1.485 Gbps/1.4835 Gbps
SD SDI: SMPTE 259M, 0.8 Vp-p, 75 ohms,
270 Mbps
3G SDI/HD SDI/SD SDI, character signal
selectable
REFERENCE IN/OUT BNC type (2), loop-through output
HD: SMPTE ST274, tri-level sync signal,
0.6 Vp-p, 75 ohms
SD: Black burst (NTSC: 0.286 Vp-p,
75 ohms/PAL: 0.3 Vp-p, 75 ohms) or
NTSC 10F-BB
Input connectors
AC IN 100/120/220 to 240 V (1)
(For details about switching the voltage,
contact a Sony service or sales
representative.)
SDI RET 1 to 4 BNC type (4)
3G SDI: SMPTE ST424/425, 2.970 Gbps/
2.967 Gbps
HD SDI: SMPTE ST292, 1.485 Gbps/
1.4835 Gbps
SD SDI: SMPTE 259M, 270 Mbps
PROMPTER 1 BNC type (2), loop-through output during
1CH mode, terminated internally at
PROMPTER 2/
75 ohms during 2CH mode, analog signal,
VBS-RET
1.0 Vp-p, 75 ohms
Output connectors
AUDIO OUT CH1, XLR 3-pin, male (2), 0 dBu/–20 dBu/
CH2 +4 dBu
CHARACTER/SYNC BNC type (1), VBS, 1 Vp-p, 75 ohms
AES/EBU BNC type (1), AES/EBU format
SDI OUT 1 to 4 3G/HD/SD SDI OUTPUT
BNC type (4)
3G SDI: SMPTE ST424/425 Level-A/B,
0.8 Vp-p, 75 ohms, 2.970 Gbps/
2.967 Gbps
HD SDI: SMPTE ST292, 0.8 Vp-p,
75 ohms, 1.485 Gbps/1.4835 Gbps
SD SDI: SMPTE 259M, 0.8 Vp-p, 75 ohms,
270 Mbps
3G SDI/HD SDI/SD SDI, character signal
selectable
UHD SDI A, B, E, F 12G/6G/3G/HD SDI OUTPUT
BNC type (2)
12G SDI: SMPTE ST2082, 0.8 Vp-p,
75 ohms, 11.88 Gbps/11.868 Gbps
6G SDI: SMPTE ST2081, 0.8 Vp-p,
75 ohms, 5.940 Gbps/5.934 Gbps
3G SDI: SMPTE ST424/425 Level-A/B,
0.8 Vp-p, 75 ohms, 2.970 Gbps/
2.967 Gbps
HD SDI: SMPTE ST292, 0.8 Vp-p,
75 ohms, 1.485 Gbps/1.4835 Gbps
UHD SDI C, D, G, H 12G/6G/3G/HD SDI I/O
BNC type (2)
12G SDI: SMPTE ST2082, 0.8 Vp-p,
75 ohms, 11.88 Gbps/11.868 Gbps
6G SDI: SMPTE ST2081, 0.8 Vp-p,
75 ohms, 5.940 Gbps/5.934 Gbps
3G SDI: SMPTE ST424/425 Level-A/B,
0.8 Vp-p, 75 ohms, 2.970 Gbps/
2.967 Gbps
HD SDI: SMPTE ST292, 0.8 Vp-p,
75 ohms, 1.485 Gbps/1.4835 Gbps
Supplied accessories
Number plates (1 set)

Before Using This Unit (1)

Operating Instructions (CD-ROM) (1)
Optional accessories
HKCU-SDI50 12G-SDI Extension Kit
HKCU-SFP50 ST 2110 Interface Kit
HKCU-SM50 Single Mode Fiber Connector Kit
HZCU-CNFG50 Config Control Software
HZCU-SNMP50 SNMP Agent Software
HZCU-UHD35 4K/HDR Processor Software
United States and Canada: Power cord set (1-551-812-XX)
Other areas: Power cord set (1-782-929-XX)
United States and Canada: Plug holder B (2-990-242-01)
Other areas: Plug holder C (3-613-640-01)
CCA-5-3 Connection Cable (3 meters), CCA-5-10 Connection
Cable (10 meters)
Service Manual
Connectors for optical/electric composite cables:
• LEMO® FXW.3K.93C (to the "CAMERA FIBER" connector on
CCU)
• LEMO® EDW.3K.93C (to the "CCU" connector on CAMERA)
Caution on the optical/electric composite cable:
For connection between the camera control unit and a camera, be
sure to use an optical/electric signal composite cable with the
connectors specified in this manual in order to comply with the limit
for EMC regulations.
Related devices
HDC5000/5500 Color Camera
HDC2000 HD Color Camera
HDC2580/2500/2400/1700 HD Color Camera
RCP-3000/1000 series Remote Control Panel
MSU-1000 series Master Setup Unit
HDCU5500
General
Power requirements 100 V to 240 V AC, 50/60 Hz
Current consumption 4.5 A (max.)
Operating –10 °C to +40 °C (14 °F to 104 °F)
temperature
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Mass Approx. 6.4 kg (14 lb 1.8 oz)
15
Specifications