Juliana Oase Montageanleitung Seite 4

May we congratulate you on your new greenhouse
GB
Dear Customer! DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time. All corresponding to the order in the assembly
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside Seen from the outside
Seen from inside Seen from outside.
SOME SAFETY PRECAUTIONS
• Assembly must only be carried out in dry and
calm weather.
Precautions.
• Always wear work gloves when installing the
• Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
• Always use working gloves while glazing.
• Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
• Assistants and especially children must be
care.
• We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
• Any ladders that are used must be placed on a
remove it with care.
level surface.
• We recommend to use protective glasses
• It is essential to have an assistant available.
while fixing the spring wire clips.
• Place the ladder on a level support.
PAGE 12: TOOLS
• It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 15: FOUNDATIONS
The column marked indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
The holes must be dug out to below the frost line
(800 mm). Place the assembled base with anchor
separately. It ensures you a stable and easy to
legs over the holes so the anchor legs fit into the
build base.
holes; it takes about 75 litres of concrete to fill up
If you make your own base the measurements
the holes.
indicated must be external measurements.
Make sure the base is completely level and square.
If you buy an original base you furthermore
To square the base, make sure the two diagonal
need about 75 litres of concrete and 6/8
measurements are identical.
plastic-/concrete pipes of about 800 mm which
The width of the front and back gables must also be
are placed in a non-freezing depth for the
identical.
fastening of the corner and middle anchors.
ATTACHMENT TO THE BASE
The base must be 100% level and square; the
If you construct your own base, you must drill holes
latter is ensured by checking that the two
(7mm) in the ground frame between all the vertical
diagonal measurements are equal.
profiles. The greenhouse must then be secured to
the base using screws (A).
Tools
If you use an original base, the greenhouse must be
The mounting of the greenhouse requires the
secured to each vertical bar as shown on drawings
tools shown on page 12.
B/C.
PAGE 14-25: ORDER OF ASSEMBLY
Page 14-27:
Place the components as shown on the illustration
Place the components as shown on the
and assemble in the order shown in the pictures. Do
illustration and assemble in the order shown
not tighten the nuts fully until the entire sub-frame
in the pictures. Do not tighten the nuts
has been assembled.
completely until the front gable construction
has been assembled.
PAGE 20-21: ROOF Page 13:
The two automatic openers should be frequently
(Fastening to the base).
adjusted and at least twice a year in response to
When constructing your own base you have
major temperature changes.
to drill holes (7 mm) in the ground frame
between all the vertical frames, the greenhouse
The cylinder allows travel of 20–30 mm for the
is then fastened to the base with screws (A).
hood. The actual cylinder can be moved up and
Using an original base the greenhouse is
down. If the rod is in the lowest position, the travel
fastened to each vertical bar as shown on
will be greatest. If the cylinder is moved upwards,
there will be less travel. drawing B/C.
If you wish to close the hood completely, move the
cylinder to its lowest position and lock it in place by
Page 24-27:
turning the screw towards the cylinder. Do not over-
For an easier assembly we recommend that you
tighten the screw.
oil the screws for the doors.
PAGE 22-25: DOORS AND WINDOWS
Fitting of glass/polycarbonate
For easier assembly, we recommend that you oil the
Important before glazing!
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
time as the profiles.
Make sure that gables and sides are level and
SIDE 25: DOWNPIPE AND FITTINGS
square, and that door(s) and window(s) are
functioning perfectly.
PAGES 26-29: FITTING OF GLASS
Important before assembly!
Best order of assembly:
Make sure that the gables and sides are level
1) Windows – 2) Roof – 3) Doors – 4) Gables
and square and that door(s) and window(s) are
– 5) Sides
functioning perfectly.
The best order of assembly for the glass:
Page 30-33:
Windows - Roof - Doors - Gables - Sides
Glazing (illustration 1 to 8)
Degrease the sheets and frames with spirit.
Glass installation (illustrations 1 to 8)
Start glazing from below, one glass at a time.
Degrease the sheets and frames with spirit.
Apply a 3 mm silicone line on the vertical
Start glazing from the bottom, one pane at a time.
frames where indicated (dotted lines on
Apply a 3mm silicone bead around the vertical
the illustration). (A 3 mm line of silicone is
frames as indicated (the dotted lines on the
illustration). (A 3mm bead of silicone is sufficient to sufficient to obtain maximum attachment). If
ensure maximum adhesion). If you use more silicone
you do use more than recommended, you can
than recommended, extra tubes can be purchased.
buy extra tubes.
If you accidentally break a pane, carefully pull the
Spring wire clips and glassholders are to be
broken glass outwards and loosen the silicone using
fitted as shown.
a sharp craft knife.
X = Spring wire clips, > = Glassholders
Clean the profile completely before inserting a new
pane of glass.
In case of broken glass carefully pull it
M-strips are fitted as shown on pages 26. Place the
outwards and loosen the silicone by means of a
upper part of the strip under the aluminium profile
sharp craft knife.
along the full length of the sheet and then click the
Clean the profile completely before inserting a
strip into position from above.
new pane of glass.
Page 34-37:
Mounting of polycarbonate
The illustrations at the bottom of page 34/36
show where to mount the polycarbonate plates
and lists. The type indication states the length
in mm. A possible adjustment is made by
means of a fine-tooth saw.
NB! To avoid the formation of algae the
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
of cardboard.
A-lists are mounted as shown on page 35/37.
Put the sheet into the bottom list, bend the
sheet slightly outwards and put it in the top list.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
profile in the whole length of the sheet and
hereafter click on the list from above.
B
Your greenhouse is now fully assembled. However,
Sealing of the polycarbonate sheets
please note the following:
The sheets may be sealed against insects.
Close the top end off with alu-tape or silicone.
MAINTENANCE
The bottom only with airstrip tape to let
• Grease the doors (hinges and locks).
condensation out (available at your local
• Keep the gutters free from leaves, etc.
dealer).
• Adjust the windows as necessary.
• Replace any broken glass.
• Now your greenhouse is completely assembled. Clean the greenhouse with disinfectant before
and after the growing season.
However, please notice the following:
WINTER PROTECTION
Maintenance
If you anticipate snow during the winter, we
• Grease doors (hinges and lock).
recommend the following winter precautions:
• Clean the gutter for leaves, etc.
• Support the apex of the roof in the middle.
• Adjustment of windows.
• Remove any deep snow from the roof.
• Replacement of broken glass.
• Take precautions to prevent snow falling from
a tree or roof, for example.
• Clean the house with disinfectant before
• Remove the cylinders for the automatic
and after the growing season.
window openers, if fitted (optional extras).
• Adjust the cylinders for the opening of the
Winter Protection
hood.
In areas with occurrence of snow we
• Secure the door(s) and window(s) to prevent
recommend the following winter protection:
wind damage to the greenhouse.
• Support the roof ridge at the centre of the
house.
WATER AND CONDENSATION
Please note that your greenhouse is not like a
• Remove greater snow loads from the roof.
conservatory, for example, and that you should
• Take precautions against snow falling
therefore be aware that the greenhouse may leak
down from for instance a tree or a roof.
during or after precipitation and that condensation
• Dismount the cylinders for the automatic
will occur on the inside of the greenhouse. Good
window openers, if any (optional extras).
ventilation will help prevent condensation.
• Secure door(s) and window(s) preventing
wind damage to the house.
INSURANCE
Please note that not all insurance companies cover
greenhouses automatically. Please contact your Insurance
insurance company to ensure that your greenhouse
Please note that not all insurance companies
is covered.
cover glasshouses automatically. Please
contact your insurance company to ensure an
GUARANTEE
insurance coverage.
Juliana greenhouses are covered by a 12-year
guarantee, which covers the replacement or repair
Guarantee
of faulty parts. The guarantee does not cover
Juliana grants a guarantee of 12 years which
polycarbonate, glass, transport, assembly, freight,
etc.
covers replacement of faulty parts. The
Juliana greenhouses are covered by a two-year
guarantee does not cover polycarbonate, glass,
warranty on painted parts, where fitted. Note that
transport, assembly, freight etc.
marks on the paint may occur due to suspension of
Juliana grants a guarantee of 2 years on painted
the profiles.
parts, if any. Note that marks in the painting
The guarantee will be void if the greenhouse is not
may occur due to suspension of the profiles.
assembled in accordance with these instructions.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
COMPLAINTS
All our greenhouses are built to the highest quality
standards. However, should you experience any
Complaints
problems, please contact your dealer at once. When
All our greenhouses are built to high standards
describing the defect, please state the greenhouse
of quality. However, should a complaint
model, the component number and the quality
occur please contact your dealer at once.
control number.
Remember to specify the defect by indicating
the greenhouse model and number of the
Any suspension marks or shiny ends on painted
component and the quality control number.
Juliana profiles will not be visible after the
greenhouse has been assembled.
Congratulations on your new greenhouse, which we
hope will bring you a lot of pleasure for many years
to come.
Yours sincerely,
Juliana Drivhuse A/S
USA