Makita HP001G Betriebsanleitung Seite 8

To change the speed, switch off the tool first. Push the
speed change lever to display "2" for high speed or "1"
for low speed. Be sure that the speed change lever is
set to the correct position before operation.
If the tool speed is coming down extremely during the
operation with display "2", push the lever to display "1"
and restart the operation.
Selecting the action mode
NOTICE:
Always set the ring correctly to your
desired mode mark. If you operate the tool with the
ring positioned halfway between the mode marks, the
tool may be damaged.
NOTICE:
Do not change the action mode while
rotating.
Adjusting the fastening torque
CAUTION:
Make sure that the dial is clean. Depending on the work environment, foreign objects such as iron
scraps or chips may adhere to the dial and cause the personal injury.
► Fig.8: 1. Dial 2. Indicator 3. Button 4. Green light
The fastening torque can be adjusted in 41 levels in low speed and 21 levels in high speed.
1. Align marking with the arrow on the tool body by turning the action mode changing ring.
2.
Pull the switch trigger and release it as soon as the indicator turns on.
3. Push the button, and the green light blinks.
4. Turn the dial, and adjust the torque level while the green light is blinking.
5. Push the button to set the value.
NOTE: After pushing the button in step 5, the green light turns off. If you adjust the torque level again, start over
from step 3.
NOTE: If you leave the green light blinking for a while, it stops blinking and the value displayed in the indicator will
be set.
NOTE: You can set the fastening torque level in two patterns; high speed and low speed.
When the lever displays "1", the torque level in low speed can be set. When the lever displays "2", the torque level
in high speed can be set.
When you change the speed with the speed change lever, the indicator blinks three times. After that, drive a trial
screw to check the speed and torque level.
NOTE: If you pull the switch trigger while the green light is blinking, the green light turns off and you will not be
able to adjust the torque level. To adjust the torque level again, release the switch trigger and turn the dial while the
green light is blinking.
NOTE: If you turn the action mode changing ring while the green light is blinking, the green light turns off and you
will not be able to adjust the torque level. To adjust the torque level again, start over from step 1.
To obtain suitable torque level, perform a test drive with a workpiece of the same material that you are going to
screw.
The following shows the rough guide of the relationship between the screw size and graduation.
Low speed
Torque level 1
Machine screw M4
Wood Soft ø3.5
screw wood x 22
(e.g.
pine)
Hard –
wood
(e.g.
lauan)
2 3 4 5 6
M5 M6
ø4.1 x 38 –
ø3.5 ø4.1 x 38
x 22
NOTE: When you change the position from "
other modes, it may be a little difficulty to slide the
action mode changing ring. In this case, switch on
and run the tool for a second at the "
then stop the tool and slide the ring to your desired
position.
► Fig.7: 1. Action mode changing ring 2. Mark
3. Arrow
This tool has three action modes.
• Drilling mode (rotation only)
• Hammer drilling mode (rotation with
hammering)
• Screwdriving mode (rotation with clutch)
Select one mode suitable for your work. Turn the
action mode changing ring and align the mark that you
selected with the arrow on the tool body.
7 8 9 10 11 12
ø5.1 x 50 –
– ø5.1 x 50
8 ENGLISH
13 14 15 16 17 18
–
ø6.2 x 63
– ø6.2 x 63
" to
" position,
19 20 21
–
–