Channel-Mode - ESX VE1200.5 Bedienungsanleitung

LOUDSPEAKER WIRING & CONNECTION
5-CHANNEL-MODE: 4 Speakers Stereo with one Subwoofer
4 OHM 4 OHM
1CH 2CH
Connections
• Connect the RCA Outputs (FRONT L & R and REAR L & R) of the head unit with the RCA Inputs (CH1 & CH2 / CH3 & CH4) of the
amplifier by using appropriate RCA Cables .
• Connect the Front-/Rear-Speakers and the Subwoofer with the Speaker Outputs (+ 1CH - & + 2CH - / + 3CH - & + 4CH - and + Mono -).
• The minimum final speaker impedance should not be lower on CH1/2/3/4 than 2 Ohms and on CH5 1 Ohms per Channel.
Input Gain
• Turn the INPUT GAIN-Control (T5 & T7) on 9V-Position (Channel 1 & 2 / 3 & 4) and the F2-Control on 6V-Position(Channel 5).
• Turn the the head unit volume to about 80-90% of its full setting.
• Turn the INPUT GAIN-Control (T5 & T7 & F8) counter clockwise until you hear some distortion.
• Then turn back the INPUT GAIN-Control (T5 & T7 & F8) slightly until you can here clean sound.
Configuration Front-Speakers Channel 1 & 2
• When you use smaller speaker systems (8.7cm - 16cm) the Input Selector should be set on HIGH PASS-Postion,because too low
• frequencies can cause damages to your speakers.The cut-off frequency should be between 60Hz - 150Hz depending on the size of the
• installed speakers and it is continously variable from adjustable via Highpass-Control T4 from 10 Hz up to 2500.
• When Phase Shift is activated by T3-Switch (On-Position) perfect soundstaging is realisable.You can virtually move the acoustic posit ion of
the subwoofer. See page 18!
Configuration Rear-Speakers Channel 3 & 4
• When you use bigger speaker systems (20cm) the Input Selector should be set on FULL-Position (Full Range-Signal).
• When you use smaller speaker systems (8.7cm - 16cm) the Input Selector should be set on HIGH PASS-Postion,because too low
• frequencies can cause damages to your speakers.The cut-off frequency should be between 60Hz - 150Hz depending on the size of the
• installed speakers and it is continously variable from 10 Hz up to 1000 Hz via Highpass-Control T6.
• When T9 is set on BP-Position the lower and upper frequency of the Bandpass Signal is adjustable by T6 & T8. See page 18!
Configuration SubwooferChannel 5
Lowpass (Channel 5) F4
• The cut-off frequency should be between 60 Hz and 100Hz, depending on the size of the installed Speaker. The cut-off frequency is
• continously variable between 35 Hz -250 Hz and is adjustable by the Lowpass-Control T8. Highpass-Control T6 is out of function!
Subsonic (Channel 5) F5
• Eliminates too low frequencies. Too low frequencies can cause damages to your speaker. The cut-off frequency should be between
• 20 Hz and 50 Hz . The cut-off frequency is continously variable between 10 Hz and 50 Hz.
Bass Boost (Channel 5) F3
• This allows you to adjust the Bass Boost between 0 - 18 dB at 40 Hz. Please use the BASS BOOST carefully.
Phase Shift (Channel 5) F6
With this Control you can virtually move the built-in position of the Subwoofer. It is continously variable between
0 and 180 degrees and it is controled by F6.
Input Selector-Schalter F8
• If there are three RCA Outputs at your head unit, you can use a third RCA to RCA cable, so you can fade the Subwoofer (Channel 5)
• via your head unit. The Input Selector-Switch should be set on 5CH-Position.
5-Channel Amplifier VE1200.5
4 OHM
3CH
4 OHM
4CH
4 OHM
5CH
Head Unit
16
MIN MAX
LEVEL
BASS REMOTE
MIN - MAX Level Controller
White LED = Operation Mode
Red LED = Protection Mode (see page 19)