Installation & Stromanschluss Q 200.2 / Q 300.2 / Q 300.4 Installationshinweise Achten Sie bei der Installation darauf, dass keine serienmäßig im Kfz vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw. entfernt werden. Vergewissern Sie sich, dass der Verstärker am Montageort genügend Kühlung erhält.
2-Kanal Verstärker - Funktionen & Bedienelemente Q 200.2 / Q 300.2 STATUS - LED FILTER / XOVER - Schalter & Regler Leuchtet diese LED grün, ist der Position HP - Hochpass ist aktiviert, d.h Frequenzgang der Lautsprecher nach unten Verstärker betriebsbereit begrenzt.
2-Kanal Verstärker - Lautsprecher & Cinchanschluss Q 200.2 / Q 300.2 2-Kanal-Betrieb: 2 Lautsprecher / Stereo Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cinch-Eingängen (INPUT) des Verstärkers mittels einer Cinchleitung. • Verbinden Sie die Front-Lautsprecher mittels geeignetem Kabel mit den Lautsprecher Ausgängen (–...
2-Kanal Verstärker - Lautsprecher & Cinchanschluss Q 200.2 / Q 300.2 1-Kanal-Betrieb: 1 Subwoofer / Mono gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge (Subwoofer Ausgang) des Steuergerätes (Radio) mit den Cinch-Eingängen (INPUT) des Verstärkers mittels einer Cinchleitung. • Verbinden Sie die Front-Lautsprecher mittels geeignetem Kabel mit den Lautsprecher Ausgängen (–...
4-Kanal Verstärker - Funktionen & Bedienelemente Q 300.4 FILTER / XOVER - Schalter & Regler pro Kanalpaar (CH1/2 & CH3/4) getrennt regelbar Position HP - Hochpass ist aktiviert, d.h Frequenzgang der Lautsprecher nach unten begrenzt. Die Trennfrequenz ist über XOVER stufenlos von 50Hz bis 250Hz regelbar Position LP - Tiefpass ist aktiviert, d.h Frequenzgang der Lautsprecher nach oben begrenzt.
4-Kanal Verstärker - Lautsprecher & Cinchanschluss Q 300.4 2-Kanal-Betrieb: 2 Subwoofer / Mono gebrückt Kabelanschlüsse • Verbinden Sie den Subwoofer-Ausgang des Steuergerätes (Radio) mit den Cincheingängen (INPUT CH1/2 & CH3/4) des Verstärkers mittels einer Cinchleitung und Y-Adaptern (SIGNAL SPLIT). • Verbinden Sie den ersten Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen (–...
Technische Daten Q 200.2 Q 300.2 Q 300.4 Kanäle Watt RMS/MAX. an 4 Ohm 2 x 75/150 2 x 100/200 4 x 55/110 2 x 100/200 2 x 150/300 4 x 75/150 Watt RMS/MAX. an 2 Ohm Watt RMS/MAX. an 4 Ohm mono gebrückt 1 x 200/400 1 x 300/600 2 x 150/300...
Fehlerbehebung Fehler: keine Funktion Ursache: 1. Die Verbindungskabel sind nicht korrekt angeschlossen. 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. 3. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen. Fehler: kein Ton aus Lautsprecher Ursache: 1.
Installation und Electrical Connection Q 200.2 / Q 300.2 / Q300.4 General Installation Notes The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and protection from moisture.
2-Channel Amplifier - Functions & Controls Q 200.2 / Q 300.2 STATUS - LED FILTER / XOVER - Switches & Controls Green Light indicates the amplifier is in Position HP - Highpass ist activated, the frequency of the speakers is bounded below. operation-mode.
2-Channel Amplifiers - Speaker & RCA-Connection Q 200.2 / Q 300.2 2-Channel-Mode: 2 Speakers / Stereo Cable Connections: • Connect the INPUT Terminals of the amplifier to the head unit line output with good quality RCA cables. • Connect the speakers with the terminal block (– CH1 + and – CH2 +) of the amplifier. •...
2-Channel Amplifiers - Speaker & RCA-Connection Q 200.2 / Q 300.2 1-Channel-Mode: 1 Subwoofer / Mono bridged Cable Connections: • Connect the INPUT Terminals of the amplifier to the head unit subwoofer output with good quality RCA cables. • Connect the speakers with the terminal block (– BRIDGED +) of the amplifier. •...
4-Channel Amplifiers - Functions & Controls Q 300.4 FILTER / XOVER - Switches & Controls Channel separated for CH1/2 & CH3/4 Position HP - Highpass ist activated, the frequency of the speakers is bounded below. The threshold is from 50Hz to 250Hz by XOVER Control adjustable. Position LP - Lowpass ist activated, the frequency of the speakers is bounded above.
4-Channel Amplifiers - Speaker & RCA-Connection Q 300.4 4-Channel-Mode: 2 Frontspeakers / Stereo & 2 Rearspeakers / Stereo Cable Connections: • Connect the head unit line outputs with good quality RCA cables with the INPUT TERMINAL of CH1/2 & CH3/4 of the amplifier. •...
4-Channel Amplifiers - Speaker & RCA-Connection Q 300.4 2-Channel-Mode: 2 Subwoofer / Mono bridged Cable Connections: • Connect the head unit subwoofer line output with good quality RCA to RCA cables and Y-Connectors (Split signal) to the AMPLIFIER INPUT CH1/2 & CH3/4 of the amplifier. •...
4-Channel Amplifiers - Speaker & RCA-Connection Q 300.4 3-Channel-Mode: 2 Speakers / Stereo & 1 Subwoofer / Mono bridged Cable Connections: • Connect the head unit line outputs with good quality RCA cables to the INPUT CH1/2 & CH3/4 of the amplifier.