Seite 1
MODEL N0: 39.5cm/15.6“ ROOF MOUNT 16:9 LCD MONITOR USER MANUAL USER MANUAL ENGLISH/GERMAN ENGLISH/GERMAN Downloaded from www.Manualslib.com manuals search engine...
This monitor is compatible with PAL and NTSC video streams – the internal video signal processing electronics automatically synchronize with PAL or NTSC video signals. Applications: The ZE-MR1502 will work in combination with any common video source unit, featuring an RCA composite video output, such as DVD-players, VCR’s or TV-tuners. Downloaded from www.Manualslib.com...
ZE-MR1502 BOX CONTENTS Part Quantity LCD Monitor IR Remote Control w/Battery A/V-Interface Metal Mounting Plate ST4.2×16 Screw Adhesive foam CM4x8 Screw User’s Manual Fuse Rubber Spacer CONTENT SAFETY INFORMATION ....................4 REMOTE CONTROL ....................5 REMOTE CONTROL FUNCTIONS ................5 USING THE REMOTE CONTROL ................
SAFETY INFORMATION 1. The unit is designed for using with a DC +12V, negative ground battery power supply, it may not be connected and/or used differently. 2. Do not operate the unit in any way other than described in this manual. Failure to follow the instructions will invalidate your warranty.
ZE-MR1502 13. Do not drop or hit the LCD panel with hard objects, as it may cause permanent damage to the unit. If you come into contact with any spilled LCD fluid, wash and clean affected areas with plenty of water and soap and seek medical attention immediately.
BATTERY Please remove the insulation plastic sheet insert from the battery holder before use. If the remote control does not function correctly or the operating range is reduced, replace the battery with a new battery (CR2025). 1. Apply pressure on the recess of the battery tray on the Pull back of remote control with a small tool.
ZE-MR1502 THE ROOF MOUNT MONITOR BASIC OPERATIONS 6 6 3 5 4 3 2 1 1. POWER Press the POWER button to switch on / off the unit. 2. MODE Select input signal AV 1 or AV 2 with MODE button.
LCD PANEL ADJUSTMENT 1. OPEN THE LCD PANEL Press Open Button to disengage the LCD panel. Pull the LCD panel outward till you reach the desired viewing angle. NOTE The LCD display opens to a maximum angle of 180° degrees. Opening it further than that may cause damages.
ZE-MR1502 MENU To adjust the picture, use the menu button to select the menu features you would like to adjust. Values of a selected feature can be adjusted by choosing the right menu entry with the “+” and “–” buttons. Use the “ ” and “...
ELECTRICAL CONNECTIONS A/V-1 A/V-2 OUTPUT Extra power for dome lights. Red: Door Switch Yellow: Car Battery Black: Common Downloaded from www.Manualslib.com manuals search engine...
Seite 11
NOTE NOTE For installation and connection we explicitely recommend to consult your ZENEC dealer. If you turn over your unit you will see a small square hole, in the tin cover near the front, with a switch inside. That switch is for adjusting the logical state of the door switch. If the built-in dome lights are on, when the doors of your car are closed, just use the switch.
INSTALLATION Step 1: Select the screw from ST4.2X16 by length that applies to your vehicle, contained in the package contents. Screw the metal mounting plate to the car roof. Please remember not to cover the opening of original dome light. Car roof girders Metal Plate Screw...
Seite 13
ZE-MR1502 Car roof girders Rubber Spacer Metal Plate Monitor CM 4x8 Screw Adhesive foam Step 7: Please double check and make sure the unit is installed properly before operation. Downloaded from www.Manualslib.com manuals search engine...
TROUBLESHOOTING Problem: Cause Solution No picture when the 1. Power wire is 1. Check the power wire display is turned on. connected improperly and replace the fuse. or fuse blown. 2. Check system cable or 2. System cable is not replace with a new one.
ZE-MR1502 SPECIFICATIONS Operating Voltage Range: Car Battery (DC +10V ~ +16V) Mechanism: Manual Open / Close Display Angle: Vertical Adjustable: Up/Down < 180° Operating Current: < 2A (Dome Light Off) Dome Light: 0.5W x 2 Operating Temperature: 0° C to +50° C Storage Temperature: -20°...
Seite 16
ZE-MR1502 Vielen Dank für den Kauf dieses ZENEC-Produktes! Mit dem Kauf des ZE-MR1502 haben Sie sich für ein technisch ausgereiftes Produkt entschieden, das Ihnen durch die Verwendung von hochwertigen Materialien und Bauteilen eine lange Lebensdauer garantiert. Bei dem ZE-MR1502 von ZENEC handelt es sich um einen 39.5cm/15.6“, 16:9 TFT-LCD Aktiv-Matrix Deckenmonitor mit Entspiegelung.
Sie die defekte Sicherung gegen ein neues Exemplar mit identischen Werten austauschen. Sollte der Kurzschluss immer noch vorhanden sein, wenden Sie sich bitte an Ihren ZENEC-Händler. 6. Achten Sie bei der Installation des Monitors darauf, dass er den Fahrer des Fahrzeuges nicht vom Verkehrsgeschehen ablenkt oder ihm in irgendeiner Weise die Sicht versperrt.
ZE-MR1502 13. Wenn Sie Fragen oder Probleme bei der Installation haben, wenden Sie sich bitte an einen ZENEC-Händler oder an den jeweiligen Landesvertrieb. DIE FERNBEDIENUNG DIE EINZELNEN TASTEN 1. [POWER]-Taste Drücken Sie die [POWER]-Taste um das Gerät ein- bzw. auszuschalten.
DIE BATTERIE Wenn die Fernbedienung nicht oder sehr langsam reagiert, müssen Sie wahrscheinlich die Batterie wechseln: 1. Öffnen Sie den Batteriefachdeckel, indem Sie die ziehen Halterung 1. nach rechts drücken und den Batterie- fachdeckel anschließend nach vorne ziehen (siehe Skizze). drücken 1 2.
ZE-MR1502 DER DECKENMONITOR DIE EINZELNEN TASTEN 6 6 3 5 4 3 2 1 1. [POWER]-Taste Drücken Sie die [POWER]-Taste um das Gerät ein- bzw. auszuschalten. 2. [MODE]-Taste Drücken Sie die [MODE]-Taste um zwischen den beiden A/V-Eingängen A/V-1 und A/V-2 zu wählen.
ÖFFNEN UND SCHLIESSEN DES DECKENMONITORS 1. ÖFFNEN DES DECKENMONITORS Drücken Sie die [OPEN]-Taste um das Display des Deckenmonitors zu öffnen und stellen Sie von Hand den gewünschten Winkel des Displays ein. BITTE BEACHTEN Der Winkel des Displays lässt sich bis zu maximal 180° einstellen. 2.
ZE-MR1502 MENÜEINSTELLUNGEN Drücken Sie eine der [MENU]-Tasten um das Menü aufzurufen. Durch wiederholtes Drücken der Tasten können Sie den Menüpunkt auswählen, welchen Sie verändern möchten. Mit den [UP /DOWN ]-Tasten ändern Sie den Wert. CONTRAST: Kontrasteinstellung BRIGHTNESS: Helligkeitseinstellung COLOR: Farbeinstellung...
INSTALLATION DES GERÄTES A/V-1 A/V-2 Gelb: 12V Rot: ACC Schwarz: GND Ausgang Stromversorgung nur für die Zusatzleuchten Rot: Türkontakt Gelb: 12V Schwarz: GND Downloaded from www.Manualslib.com manuals search engine...
Seite 25
ZE-MR1502 HINWEIS HINWEIS empfehlen ausdrücklich Montage Anschluß einem Fachmann bzw. in einem Fachbetrieb durchführen zu lassen. Ihr ACR-Händler hilft Ihnen hier gerne weiter. Wenn Sie das Gerät kopfüber betrachten sehen Sie vorne ein kleines viereckiges Loch in einer Blechabdeckung. Der dort befindliche Schalter dient zur Anpassung an den Türkontakt (Öffner- o.
MONTAGE DES GERÄTES Schritt 1: Befestigen Sie die Montageplatte unter Berücksichtigung der richtigen Schraubenlänge (Lieferumfang ST 4.2x16) am Dach Ihres Fahrzeuges (siehe folgende Skizze). Beachten Sie dass die Öffnung der originalen Innenraumbeleuchtung durch die Montageplatte nicht verdeckt wird. Dachholme des Fahrzeuges Montageplatte Schrauben ST4.2x16...
Seite 27
ZE-MR1502 Dachholme des Fahrzeuges Distanzgummi Montageplatte Monitor CM 4x8 Schrauben Abdeckungen Schritt 7: Überprüfen Sie noch einmal die Installation und alle Funktionen des Gerätes. Downloaded from www.Manualslib.com manuals search engine...
Fernbedienung ist leer. Batterie in die Fernbedienung ein. 2. Die Fernbedienung ist defekt. 2. Wenden Sie sich an einen ZENEC-Händler um die Fernbedienung auszutauschen. Das Bild ist zu dunkel. 1. Die Umgebungs- 1. Dieser Effekt ist typisch für temperatur ist zu niedrig.
ZE-MR1502 SPEZIFIKATIONEN Spannungsversorgung: +10V ~ +16V (DC) Mechanismus: Manuell Kippwinkel: < 180° Stromverbrauch: < 2A (Beleuchtung aus) Beleuchtung: 0,5W x 2 Betriebstemparatur: 0° C bis +50° C Lagertemparatur: -20° C bis +60° C Abmessungen (mm): 384 x 340 x 47 (H x B x T)
2 YEARS LIMITED WARRANTY Dear customer Thank you for purchasing this ZENEC product. It is advisable to keep the original packing material for any future transporting of the product. Should your ZENEC product require warranty service, please return it to the retailer from whom it was purchased or the distributor in your country.
Seite 31
WARRANTY/GARANTIE ZENEC MODEL: ZE-MR1502 Serial Number: ..........................Date of Purchase: ......................... Your name: ............................ Your address: ..........................City: .............................. State: ........ZIP or Postal Code ................. Country: ............................Dealer’s address & stamp Downloaded from www.Manualslib.com manuals search engine...
Seite 32
ZENEC by ACR AG · Bohrturmweg 1 · Bad Zurzach · Switzerland JL/Ver. 1.01 Downloaded from www.Manualslib.com manuals search engine...