Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Armed/Partially armed
Disarmed
Armed with battery low
Disarmed with battery low
Armed with Tamper open
Disarmed with Tamper open
Entrance/exit sounds
* The audio indications of the siren also relate to the settings made on the control unit. Refer to the programming manual.
Siren configuration
Learning
Step 1:
Remove the screw from the bottom of the siren and remove the upper cover.
Step 2:
Undo the two screws fixing the LED cover and remove the LED cover.
Step 3:
Set the control unit to learning mode; see the instruction manual of the control
unit for details.
Step 4:
Power the siren. All the LEDs will blink once and the buzzer will beep once.
Step 5:
Press the Learn button once. The siren will beep once and the LED groups 1 and 3
will light up for a short time. Now the siren is in learning mode and will transmit to
the control unit.
Step 6:
If the control unit has not received a learning code, press the learning button again
(the siren will not sound this time).
Step 7:
If the control unit receives the learning code, proceed on the control unit as
shown in its instruction manual. A confirmation message will be sent to the
siren. After having received the confirmation message, the siren will beep once
and the LED group 2 will blink once to indicate that the learning process was
successful. At that point, the siren will exit learning mode.
<
N
O
T
E
>
<
N
O
T
E
>
If the siren does not receive the confirmation code from the control unit within one minute, the siren will exit learning
mode and the LED groups 1 and 3 will be switched off.
Installation
Proceed with the installation after having concluded the learning operation.
Step 1: Deactivate the tamper function on the control unit. If the siren is installed on MP500/xx, access "Maintenance" mode
(see the instruction manual of the control unit for details). The siren will generate an acoustic signal to indicate that
the Tamper switch is off.
<
<
N
N
O
O
T
T
E
E
>
>
The Tamper function will remain OFF for one hour. The control unit will return the function automatically back to ON
after this period of time.
Step 2:
Find the point where to install the siren.
Step 3:
Remove the upper cover by removing the screw on the bottom and carefully extracting the external container.
Step 4:
Remove the LED cover by loosening the two screws which fix it.
Step 5:
Power the siren by setting the switch to position BT4.
Step 6:
Check the radio connection level by setting the control unit in Walk Test mode and pressing the learn button.
Step 7:
If the test is successful, position the LED cover and fix it with two screws.
Step 8:
Identify the four mounting holes, install and fix the siren to the wall using the large screws and the anchor bolts
provided. Tighten the screws and make sure that the Tamper switch is fully pressed against the wall. If there is a
gap, fill it with suitable spacer material.
Step 9:
Reposition the upper cover by coupling it to the top of the base. Press the bottom of the upper cover onto the base
and tighten the screw of the bottom.
Step 10:
Reactivate the tamper function on the control unit. If the siren is installed on MP500/xx, exit "Maintenance" mode
(see the instruction manual of the control unit for details).
DS80HP8A-001E
Siren audio
1 beeps*
3 LED groups blink once
2 beeps*
Blinking in sequence for 1 cycle
3 beeps
3 LED groups blink 3 times
3 beeps
Blinking in sequence for 3 cycles
5 beeps
3 LED groups blink 5 times
5 beeps
Blinking in sequence for 5 cycles
Countdown beeps
Light alarm indication
Upper cover
Lower screw
9
Werbung
Inhaltsverzeichnis
