Troubleshooting - Landxcape LX790 Benutzerhandbuch

Error unknown.
NOTES
• Before turning power on, always return Landxcape
TM
Landxcape is sitting over the boundary wire when turned on.
• If for any reason—i.e. a party, children playing...—you want to park your Landxcape
will go to its charging base and stay there. Press
• If an error repeatedly occurs in the same area of your lawn, you might have a problem with the boundary wire. Please refer to the Installation
Guide and check your set up with its help.
• If your lawn is divided in two separate areas connected by a corridor less than 1m, one of which is not provided with the charging base: when
TM
Landxcape runs out of charge, take it manually to the charging base, the charge process will start.
TM
• If Landxcape runs abnormally once in a while, please try to restart it. If the problem is not resolved, try to removing and reinstalling the
battery . If the problem is still not resolved, please contact a Landxcape
• Do not wash your Landxcape
11.

Troubleshooting

TM
If your Landxcape does not work correctly, follow the troubleshooting guide below. If the issue persists, contact your Dealer.
Symptom
The LED light on the charging base does
not turn on.
Red light turns on the charging base.
TM
Landxcape turns on, but the blade
disc does not move.
TM
Landxcape vibrates.
Grass is being cut unevenly.
TM
Your Landxcape is inside its territory
and the boundary wire is connected.
And " " is displayed.
The charging time is far more than the
rated charging time.
EN
Restart Landxcape
contact a service agent for help.
TM
to its territory. If not, "
to turn Landxcape
TM
with a high pressure washer. This could cause damage to the battery or the machine.
Cause
There is no power.
The boundary wire isn't connected.
TM
Landxcape is searching for the charging
base (unless you press
make it go to the charging base)
Blades may be damaged. Check condition of
the blade disc.
TM
Landxcape does not work enough hours per
day.
Mowing area is too big.
Blades are dull.
The cutting height is too low for the length of
the grass.
Grass or other object has wrapped around the
blade disc.
There is a build-up of grass in the blade disc or
motor frame box.
The boundary wire ends are clamped
incorrectly.
The boundary wire is broken.
Poor connection caused by debris on the
charging strip.
The charging protection program has activated
due to high temperature.
TM
. Press then . If the error message is still displayed,
" will be displayed. This message is also displayed when
TM
in the charging base: Press
TM
off.
TM
service agent for help.
Check the charging base is connected properly to the
charger and the charger is connected to a suitable
power supply.
Check that the boundary wire has been connected
correctly to the charging base.
Check there are no breaks in the boundary wire, especially
in the wire ends.
This is normal. Landxcape
then button to blade disc does not rotate while it is searching for the
charging base automatically.
Check the blades, and replace them if damaged.
Remove debris and foreign objects from the blades
and blade disc.
Add more hours to the scheduled mowing time.
Try decreasing the size of the mowing area or adding
more hours to the mowing time.
Change all the blades and screws in order to balance
the blade disc.
Raise the cutting height and then gradually lower.
Check the blade disc and remove the grass or other
object.
Make sure the blade disc rotates easily. If need be, you
may take off the blade disc and remove the debris.
Reverse the boundary wire ends.
Repair damaged boundary wire with connectors.
Clean the contact pins located on the charging base
and the charging strip on Landxcape
Place the charging base in a shady area or wait until
the temperature has cooled down.
TM
then . Landxcape
Action
TM
needs to recharge, the
TM
using a cloth.
19