Maintenance; Software-Update - Landxcape LX790 Benutzerhandbuch

is the recommended distance. The provided distance gauge ensures
proper installation.
If your neighbor also uses a Landxcape
metre between your boundary wire and your neighbor's.
The boundary wire must outline the intended mowing area
exactly. Your Landxcape
TM
will become confused by extra bends or
coils of boundary wire that are not part of its mowing area (See Fig.
G). If there is excess boundary wire after the mowing area has been
outlined, cut it off and store this additional wire in a separate location.
It is important to leave the necessary length where it connects to the
charging base so it can be connected and still remain buried.
6.2 Burying the Boundary Wire
If you are planning to bury the boundary wire, it is recommended to first
peg it down. This allows you to easily change the layout if necessary before
burying the wire. When the boundary wire installation is complete, have
TM
Landxcape follow and check the path by pressing
TM
allows your Landxcape to adjust to its new environment. .
TM
While observing Landxcape you can easily make alterations to the
boundary wire to ensure Landxcape
the charging station. Confirm that Landxcape
station successfully, and bury the wire if desired.
6.3 Joining the boundary wire
If you want to extend and splice the boundary wire, use a connector.
The connector is waterproof and provides optimal connection.
Insert both wire ends in any two of the three holes of the connector.
Insert the wires fully until both wire ends are visible on the other side of
the connector. (See Fig. H) Press the connector together by using a pair
of pliers. (See Fig. I, J)
WARNING! It is not recommended to simply splice the boundary
wire with insulating tape or use a screw terminal block for
connection. A broken circuit may occur after a period of time as soil
moisture can oxidize the wire.
7. Software update
The software can be updated when new versions become available.
The latest software can be downloaded from our website
www.landxcape-robotics.com.
Update via USB. See below for download and installation instructions:
(1) Locate the latest software version at: www.landxcape-robotics.
com. Save the file to an empty FAT32 formatted USB (flash drive).
Delete any other files on the drive and check the format. If the drive
is not formatted in FAT32 , please reformat the drive.
NOTE: the software update is downloaded as a zipped file. You will
need to unzip or extract it before proceeding.
TM
(2) Place Landxcape on a secure and level surface. Press
TM
off your Landxcape .
(3) Insert the USB drive (flash drive) in the port. (See Fig. K1)
TM
(4) Turn Landxcape on. The update will begin automatically. Wait until
the display shows " " (See Fig. K2), then remove the USB drive
(flash drive) and tightly close the protective cover. When the display
shows " ", the update is complete and Landxcape
the PIN page.
The manual included with your Landxcape
software at the time of production. Some new features/functions in the
new version may not exist in the manual. If you found some settings not
16
TM
, keep a spacing of at least 1
and . This
TM
's trouble-free tracking when locating
TM
docks in the charging
to turn
TM
will enter
TM
is based on the default
in the manual, please visit www.landxcape-robotics.com to download
the latest manual.

8. Maintenance

TM
Your Landxcape works hard and needs to be cleaned and checked
from time to time. Some parts will require replacement as they become
TM
worn. Never use your Landxcape
Switch off the machine before carrying out any service or maintenance.
Here's how to take care of your Landxcape
8.1 Keep it sharp
WARNING: Before cleaning, adjusting, or replacing the
blades, turn your Landxcape
gloves.
WARNING: When fitting new blades, make sure you
replace ALL the blades. Always use new screws when
fitting blades. This is important to ensure blade retention and
balance the blade turning disc. Failure to use new screws could
cause serious injury.
TM
Landxcape does not cut grass like other mowers. Its cutting blades
are razor sharp on 2 edges and rotate in both directions for maximum
cutting capacity (See Fig. L). Each blade of your Landxcape
cutting edges. The blade turning disc will make forward and reverse
rotation at random to use both cutting edges and minimize the
frequency of replacing the blades. Each cutting blade will last up to
2 months when it is programmed to mow everyday. Always check to
see if the blades are chipped or damaged and replace them if they
are. When the cutting blades are dull and worn out, they should be
replaced with the spare blades provided with your Landxcape
blades are also available at your nearest Landxcape
A. Replace the Blades
After some time, usually every season, your Landxcape
will need to be replaced. When replacing the blades, make sure to
replace ALL of them at the same time. You can replace them with one
of the spare blade kits and extra blade screws supplied with your
TM
Landxcape .
Before attempting to replace your Landxcape
power off and put on protective gloves and follow these steps:
TM
1. Gently flip Landxcape over.
2. Remove the battery cover and remove the battery.
3. Take the screws off the blades with a screwdriver. (See Fig. M)
4. Firmly screw on the new blades.
5. Refit the battery and the battery cover.
IMPORTANT: After screwing the blade to the blade disc, make
sure the blade is able to spin freely.
8.2 Keep it clean
WARNING: Before cleaning, turn your Landxcape
Put on protective gloves before cleaning the blade
turning disc and do not rinse or flush with water.
A. Cleaning the body
TM
Your Landxcape will live a much happier and longer life if it is
cleaned regularly. Although, since your Landxcape
machine, you will need to take care when cleaning. DO NOT use a
hose, high pressure washers and do not pour running water on
your Landxcape TM . It is best to use a spray bottle filled with water.
When cleaning the machine body, use a soft brush or clean cloth and
avoid using solvents or polishes (See Fig. N). Lastly, remove all build
with defective main switch.
TM
.
TM OFF and put on protective
TM
has 2
TM
. Spare
TM
retailer.
TM
's Blades
TM
's blades, turn the
TM OFF.
TM
is an electric
EN