Operation - Makita DTWA070 Betriebsanleitung

Alarm No.
- A larm f or no c om-
munic ation w ith
th e P C
- I nd ic ation th at th e
tool c an c ommuni-
c ate w ith th e P C
- C h ec k f or th e lamp
and beeper ( w h en
th e battery c artrid ge
is installed )
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct impact socket
A l w a y s use t h e c orre c t si z e impa c t so c ket f or bolts an d nuts.
A n in c orre c t si z e impa c t so c ket w ill result in ina c c urate an d
in c onsistent f astening tor q ue an d / or d amage to t h e bolt or nut.
Installing or removing impact socket
Optional accessory
CAUTION:
Make sure that the impact socket
and the mounting portion are not damaged before
installing the impact socket.
CAUTION:
After inserting the impact socket,
make sure that it is rmly secured. If it comes out,
do not use it.
NOTE: T h e w a y o f impa c t so c ket installation v aries
d epen d ing on t h e t y pe o f t h e s q uare d ri v e on t h e tool.
Tool with the ring spring
For impact socket without O-ring and pin
Fig.13: 1. I mpa c t so c ket 2. S q uare d ri v e 3. R ing spring
P us h t h e impa c t so c ket onto t h e s q uare d ri v e until it
lo c ks into pla c e.
T o remo v e t h e impa c t so c ket, simpl y pull it o f f .
For impact socket with O-ring and pin
Fig.14: 1. I mpa c t so c ket 2. O -ring 3. P in
Mov e th e O -ring out of th e groov e in th e impac t soc ket
and remov e th e pin f rom th e impac t soc ket. F it th e impac t
soc ket onto th e sq uare d riv e so th at th e h ole in th e impac t
soc ket is aligned w ith th e h ole in th e sq uare d riv e.
I nsert t h e pin t h roug h t h e h ole in t h e impa c t so c ket an d
s q uare d ri v e. T h en return t h e O -ring to t h e original posi-
tion in t h e impa c t so c ket groo v e to retain t h e pin.
T o remo v e t h e impa c t so c ket, f ollo w t h e installation
pro c e d ures in re v erse.
Function Status of the tool
No d ata c ommu-
nic ation w h ile th e
tool is c onnec ted to
th e P C .
T h e tool is c on-
nec ted to th e P C
and able to c ommu-
nic ate w ith .
T h e tool perf orms
th e operation test
f or th e L ED ind ic ator
( green/ red ) , ligh t,
and beeper.
Status of the LED indicator/beeper
LED indicator
Blinks in y ellow .
Blinks in green.
T h e L ED ind ic ator
ligh ts up in green
and th en red . A f ter
th at, th e ligh t turns
on f or a w h ile.
Tool with the detent pin
Fig.15: 1. I mpa c t so c ket 2. H ole 3. S q uare d ri v e
4. D etent pin
A lign t h e h ole in t h e si d e o f t h e impa c t so c ket w it h t h e
d etent pin on t h e s q uare d ri v e an d pus h t h e impa c t
so c ket onto t h e s q uare d ri v e until it lo c ks into pla c e. T ap
it lig h tl y i f re q uire d .
T o remo v e t h e impa c t so c ket, simpl y pull it o f f . I f it is
h ar d to remo v e, d epress t h e d etent pin w h ile pulling t h e
impa c t so c ket.
Installing hook
Optional accessory
T h e h ook is use f ul to h ang t h e tool. I nstall t h e h ook to
t h e h oles on t h e tool bo d y .
Fig.16: 1. H ook 2. H ole

OPERATION

CAUTION:
Always insert the battery cartridge
all the way until it locks in place. I f y ou c an see t h e
re d in d i c ator on t h e upper si d e o f t h e button, it is not
lo c ke d c ompletel y . I nsert it f ull y until t h e re d in d i c ator
c annot be seen. I f not, it ma y a c c i d entall y f all out o f
the tool, causing injury to you or someone around
y ou.
CAUTION:
Hold the tool firmly and place the
impa c t so c ket o v er t h e bolt or nut. T urn t h e tool on
an d f asten f or t h e proper f astening time.
CAUTION:
I f t h e tool is operate d c ontinuousl y
until t h e batter y c artri d ge h as d is c h arge d , allo w t h e
tool to rest f or 1 5 minutes be f ore pro c ee d ing w it h a
f res h batter y c artri d ge.
CAUTION:
Pressing excessively on the tool
will not speed up the drilling. I n f a c t, t h is e x c essi v e
pressure w ill onl y ser v e to d amage t h e tip o f y our d rill
bit, d e c rease t h e tool per f orman c e an d s h orten t h e
ser v i c e li f e o f t h e tool.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
12 ENGLISH
Action to be taken
Beeper
– R estart th e appli-
c ation sof tw are and
re-c onnec t th e U S B
c able.
–
A series of v ery
sh ort beeps
–
–