Operation - Renkforce RS2W Bedienungsanleitung

• Adhesive attachment
Use double-sided adhesive tape to attach the radio motion detector to an appropriate surface.
This surface must be smooth, dust and grease-free.
• Screw assembly
Remove the cover with the PIR window by inserting a flat-head screwdriver between frame
and cover and subsequently levering out the cover carefully. Keep the alignment of the housing
parts in mind (see chapter "Inserting, replacing the batteries").
Remove the central section (with the electronics) from the frame by loosening the lateral clips.
The frame can now be attached with 2 - 4
suitable screws and, if appropriate, dowels.
Pay attention when drilling and tightening
the screws that no cable or pipes are dam-
aged.
Reassemble the radio motion detector in
reverse order.

Operation

Keep a minimum distance of 20 - 30 cm between the radio motion detector and the radio
receiver.
a) Resetting the radio motion detector
At initial start-up, you should first perform a reset and only then program the radio receiver(s).
A reset also deletes all radio receivers tuned in/saved (e.g. when you want to reset the radio mo-
tion detector to the default setting).
Proceed as follows to perform a reset:
• Press and hold down the control button (3) of the radio motion detector (for about 3 seconds)
until the LED (2) flashes. Release the button again. The LED (2) continues to flash.
• Press and hold down the control button (3) again for approx. 6 seconds. The LED (2) goes out
briefly during this time, then blinks a few times and then goes out again. Now release the button.
b) Programming a radio receiver to the radio motion detector
It is possible to program up to 5 different radio receivers at every radio transmitter of
the RS2W radio system (e.g. radio-controlled switch socket).
However, a dimmer should not be programmed at the radio motion detector.
• Switch off the radio receiver of the RS2W radio system that you want to program using its con-
trol button (see operating instructions for the radio receiver used).
• Press and hold down the control button (3) of the radio motion detector (for about 3 seconds)
until the LED (2) flashes. Release the button again.
• Press and hold down the control button of the radio receiver until the programming process at
the radio motion detector is complete; as a result, the LED (2) goes out.
• The radio receiver switches on to indicate the end of the programming process.
If 5 radio receivers have already been programmed on the radio motion detector, the
LED (2) flashes during an attempt to program another radio receiver as described
above.
However, the radio receiver is not programmed and it does not respond to the radio
motion detector.
c) Deleting a radio receiver from the radio motion detector
Please proceed as described in the programming process.
d) Functional test (manually switching on/off)
Briefly press the control button (3) to switch the programmed radio receiver on or off. That way
you can perform a functional test. For this purpose, observe the description of the LED's function,
see section g) below.
e) Setting the switching threshold for the ambient brightness
You can use the sliding switch for the ambient brightness (4) to set the brightness in 4 stages defin-
ing at which ambient brightness the PIR sensor in the radio motion detector shall be activated and
start detecting temperature changes in the detection area.
The more you push the sliding switch towards the moon symbol, the darker it has to be in order
for the PIR sensor to function. In that case, the programmed radio receiver will be activated only
at night.
When the sliding switch is pushed fully in direction of the sun symbol, the radio motion detector
also works in the daytime.
f) Setting the on-time
With the sliding switch (1) you can set the on-time for the programmed radio receiver (adjustable
in a time range of 6 seconds, 15 seconds, 1 minute and 5 minutes).
g) Function
If the PIR sensor detects a temperature change in the detection area, the radio motion switch ac-
tivates the programmed radio receiver (depending on the set switching threshold for the ambient
brightness, see above) for the preset on-time. When the set time has passed, the radio receiver
is switched off again.
If more than one radio receiver is programmed at the radio motion detector (up to 5 are
possible), all radio receivers are switched on or off.
If the radio receiver recognises the switching command, it sends a confirmation back to the radio
motion detector. In this process, the LED of the radio motion detector briefly flashes 1x. If there is
no confirmation, the radio motion detector LED flashes several times.
In this way, you can always see if the radio receiver (e.g. a radio-controlled switch socket) has
executed the switching command or not.
If more than one radio receiver is programmed at the radio motion detector (up to 5 are
possible), the LED only briefly flashes 1x when all radio receivers have recognized the
switching command and the radio motion detector has received the confirmation.
h) Deleting a defect/lost radio receiver
It goes without saying that defect or lost radio receivers can no longer be deleted from the radio
motion detector (see above under section c).
Perform a reset at the radio motion detector (see above under section a). Here, however, all pro-
grammed radio receivers are deleted from the radio motion detector and must be programmed
again.
Maintenance and cleaning
Apart from the occasional battery change, the product is maintenance-free.
Clean the product with a soft, clean, dry cloth.
Do not use aggressive cleaning agents or solvents since these damage the housing or the func-
tioning may be impaired.
Declaration of conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Street 1, D-92240 Hirschau hereby declare that this prod-
uct is in compliance with the essential requirements and other relevant provisions of directive
1999/5/EG.
The declaration of conformity for this product is available at:
www.conrad.com
Range
The transmission range of the radio signals between the radio motion detector and the radio re-
ceiver is up to 150 m under optimum conditions.
This value, however, is the so-called "open space range" (the range when transmitter
and receiver are visible to each other, without interfering influences).
In practice, however, there are walls, ceilings, etc. between the transmitter and receiver, thus the
range is reduced accordingly.
Due to the different influences on the radio transmission, no specific range can be guaranteed.
However, trouble-free operation is usually possible in a single family house.
Sometimes the range can be considerably reduced due to:
• Walls, reinforced concrete floors, drywall walls with metal frame construction
• Coated/metallised insulated glass
• Proximity to metallic & conductive objects (e.g., heating elements)
• Proximity to human bodies
• Other devices on the same frequency (e.g. radio headphones, radio-controlled speakers)
• Proximity to electric motors / appliances, transformers, power supplies, computers
Disposal
a) General instructions
Please dispose of the unserviceable product according to the relevant statutory re-
quirements.
Remove the inserted batteries and dispose it of separately from the product.
b) Disposal of used batteries
As a consumer you are legally bound (battery ordinance) to return all used batteries; disposal in
the household waste is prohibited!
Batteries containing hazardous substance are marked by the symbols alongside which
indicate the prohibition of disposal with domestic waste. The symbols of the critical
heavy metals are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
You can return flat batteries/rechargeable batteries free of charge to the collection points in your
community, at our branches or anywhere else where batteries/rechargeable batteries are sold!
That way you are fulfilling your statutory obligations and you are contributing to the protection of
the environment!
Technical data
Power supply ............................................................. 2x batteries of type AAA/Micro
Transmission/ reception frequency ....................... 868.3 MHz
Range .......................................................................... up to 150 m (see chapter "Range")
Max. number of receivers ....................................... 5
PIR range .................................................................... up to 8 m (see chapter "Functional description")
PIR detection angle .................................................. 140° horizontal , 90° vertical
On-time ....................................................................... adjustable 6 s, 15 s, 1 min, 5 min
Switching threshold for ambient brightness ........ adjustable in 4 stages
Ambient conditions ................................................... Temperature 0 °C to +45 °C; Humidity 0% to 90%
Dimensions (W x H x D)............................................ 80 x 80 x 27.5 mm
Weight ......................................................................... approx. 57 g (without batteries)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
relative, non-condensing