Troubleshooting - ION Stereo LP Schnellstartanleitung

Troubleshooting

If you experience any difficulties, please refer to the troubleshooting steps below as well as those in
the EZ Vinyl/Tape Converter manual included with this product.
I'm not hearing any audio when recording music to a computer:
I'm not hearing any audio when playing music:
• If you are playing music from vinyl:
• If you are playing music from your computer:
I am hearing a hum through my speaker or laptop when using the turntable:
• If you are recording to a laptop:
• If you are playing through a speaker:
My turntable is not making any sound, or music is muffled:
The turntable belt fell off:
My turntable is not spinning:
My record is not playing at the correct speed; its pitch is too high or too low:
6
Downloaded from www.Manualslib.com
o Make sure that Stereo LP is powered on and that the needle is on the record.
o Make Stereo LP is selected as your computer's default recording device (see the instructions
below).
o Disconnect then reconnect the USB cable connecting Stereo LP to your computer.
Make sure the computer speakers are turned up and the volume is not muted. Try turning up the
volume on the Stereo LP's built-in speakers using the volume knob on the top panel of Stereo
LP.
o If you are listening through your computer's speakers, make sure those speakers are selected as
your computer's default playback device (see the instructions below). Alternatively, you could
connect Stereo LP's RCA outputs to a stereo system or powered speakers. Do not connect
them to phono-level inputs; Stereo LP's RCA outputs are line-level and could damage a device
with phono-level inputs.
(Note: The RCA outputs monitor the signal coming out of the turntable, not the signal coming
from your computer.)
o Make sure that Stereo LP is powered on and that the needle is on the record.
o Connect Stereo LP's RCA outputs to a stereo system or powered speakers.
(Do not connect them to phono-level inputs; Stereo LP's RCA outputs are line-level and could
damage a device with phono-level inputs.)
o Make sure to adjust the volume knob on the turntable in order to hear your vinyl record playing
through the built-in speakers.
o Make sure your software music player's volume is turned up.
o Make sure your computer's volume is turned up.
o Make sure your computer's speakers are selected as your computer's default playback device
(see the instructions below). (Stereo LP cannot be used as a playback device for your
computer's audio.)
Please connect the laptop to a grounded power supply (3 prong).
o
o Ensure you are using the power adapter that was included with your product.
o If your volume is on max, try turning it down until the hum stops.
o Take the cover off the stylus.
o Please re-attach the belt to the turntable. For details on how to do this, see the guide located at
ionaudio.com/turntablebelt.
o Ensure the turntable is powered on (power switch in the back).
o Ensure autostop is turned on and the tonearm is placed over record (if auto stop is off it should
always be spinning when power is on).
o If the above steps do not help, you may need to re-attach your turntable belt.
For details on how to do this, see the guide located at ionaudio.com/turntablebelt.
o Ensure the 33 / 45 / 78 switch is set to the correct speed for your record.
o If the 33 / 45 / 78 switch is set correctly and the speed it still slightly off, do the following:
1. On the underside of Stereo LP, find the rubber pad with the RPM speed you want to
adjust, and gently lift up the rubber pad to remove it.
2. For the 45 and 33 RPM setting, push through the rubber seal, and tighten/loosen the
screw using a Phillips-head screwdriver to fine-tune the RPM speed.
3. For the 78 RPM setting, tighten/loosen the screw using a flat-head screwdriver.
manuals search engine