ION Stereo LP Schnellstartanleitung Seite 5

Features
1. Platter: Place your record here.
2. Tonearm*: The tonearm can be raised and lowered
by hand, or by pressing the raise / lower lever.
Please note that the tonearm needs to be moved
away from resting position (on the arm clip) for the
turntable motor to activate. When the tonearm is
placed back in its resting position, the turntable
motor will deactivate if Autostop has been turned on.
3. Arm Clip: This specially designed arm clip secures
the tonearm while at rest or when not in use. The arm
clip has been designed to remain in the up position
while unlocked.
4. Raise / Lower Lever: Raises and lowers the
tonearm.
5. 33 / 45 / 78 Switch: This switch controls the
RPM of the turntable platter. If the record is
not playing at the correct speed, see the
Troubleshooting section for details on how to
resolve this.
Note: For best results when playing 78 RPM
vinyl records, use a 78 RPM stylus (sold
separately). Only use a 78 RPM stylus with 78
RPM vinyl records. Purchase a 78 RPM stylus
at ionaudio.com.
6. 45 RPM Adapter Holder: Holds the included
45 RPM adapter. When not using the adapter,
please place it in this holder.
7. Autostop Switch: This switch turns autostop
on or off. When autostop is on, the platter will
start spinning when the tonearm is placed over
the record and stop spinning when the record
has reached the end. (When autostop is off, the platter will
always spin regardless of the position of the tonearm.)
Note: If your vinyl record stops before it reaches the end of
the music, turn Autostop to the off position for this particular
record. This is generally recommended for 45 RPM records.
8. Headshell: ION headshell with stylus and ceramic cartridge.
Remove the plastic cover off the stylus before playing a record.
Note: For best results when playing 78 RPM vinyl records, use a 78 RPM stylus (sold separately). Only
use a 78 RPM stylus with 78 RPM vinyl records. Purchase a 78 RPM stylus at ionaudio.com.
9. Speakers: Listen to the audio from your playing vinyl record.
10. Volume: Controls the audio output level of the internal speakers and the headphone output.
11. Headphone Jack: Connect headphones (sold separately) to listen to your vinyl playback.
12. Aux Input: Connect another audio source, such as cassette tapes, to this stereo 1/8" (3.5 mm) input
to digitally convert the source through a USB connection to a computer.
13. RCA Output**: The audio from a playing vinyl record is sent to this line-level coaxial audio output.
This must not be connected to phono level devices. (If you do not already have an RCA cable, this can
be found at a local electronics retailer.)
14. USB Audio Output: Use the included USB cable to connect your turntable to your computer. The
USB connection will send audio from the turntable to your computer.
Please see the Using Stereo LP with Your Computer section of this manual for information.
15. Power: Use the included adapter to connect to wall power.
16. Power Button: Press this button to turn Stereo LP on/off.
Downloaded from www.Manualslib.com manuals search engine
9
IMPORTANT: Remove the plastic cartridge cover
(needle cover) before operating the turntable.
* IMPORTANT: A replacement cartridge/stylus
can be purchased by contacting the ION Audio
Parts Dept. at 401-658-3743 (U.S.), emailing
parts@ionaudio.com, or by visiting ionaudio.com.
** WARNING: The RCA outputs are LINE level.
Please only connect these to LINE level inputs.
You may damage your receiver if you plug in a
LINE level device into a PHONO level input.
12 13
6
2
1
4
5
3
7
8
10
9
11
15
16
14
5