Imperia restaurant R.B.T. Gebrauchsanleitung Seite 9

1 - Place the machine on a suitable surface.
2 - Fit the roll and cut accessory (B) on to the supports (C2).
3 - Fit the pasta hopper (A) on to the supports (C1) with the wooden roller (A1) positioned downwards.
4 - Plug in the machine and turn the master switch to position "RED". The machine will start moving so that
the transmission arm (F) can be inserted.
5 - Fit the transmission arm (F) pushing the pins into the holes on the side of the machine and the dough mixer.
The short pin (F1) fits into the hole (G1) on the side of the machine and the long pin (F2) fits into the hole (H2) on the
side of the dough mixer.
6 - Insert the previously processed dough between the accessory cutter rollers, as mentioned in point 5 of use of the machine.
TO DISMANTLE THE MACHINE (on finishing work): turn the master switch to position "GREEN", remove the plug from the socket.
Remove the transmission arm (F) and release the roll and cut accessory from the supports (C1). Remove the pasta hopper.
AFTER USE: follow the instructions described in the paragraph "Cleaning and maintenance".
GENERAL WARNING.
Remember that the safety device prevents the machine from operating when the roller
(A1) is not lowered.
USE OF THE MANUAL SIMPLEX CUTTING
AND ROLL ACCESSORY (fig.8)
BEFORE USE: follow the instructions in the paragraph "Cleaning and maintenance";
1 - Place the machine on a suitable surface.
2 - Fit the roll and cut accessory (B) on to the supports (C2).
3 - Fit the handle (M) into the appropriate hole and proceed with the manual working of the pre-prepared sheet of pasta.
TO DISMANTLE THE MACHINE (after use) remove the handle (M) and release the roll and cut accessory (B) from the
supports (C2).
AFTER USE: follow the instructions described in the paragraph "Cleaning and maintenance".
USING THE DOUGH MIXER AND THE SIMPLEX ROLL AND
CUT ACCESSORIES TOGETHER (fig.9)
The electronic machine Imperia Restaurant (R.M.N.) can operate the two accessories together to prepare and at the
same time manually cut the sheet of pasta. The following instructions explain how to go about this operation.
BEFORE USING: follow the instructions described in the paragraph "Cleaning and Maintenance".
1 - Follow the instructions for "Using the Dough Mixer"
2 - Fit the roll and cut accessory into the supports (C2)
3 - Fit the handle (M) into the hole (G2).Cut the pasta sheet manually.
TO DISMANTLE THE MACHINE (on finishing work): turn the master switch to position "GREEN", remove the plug from
the socket. Remove the transmission arm (F) and the handle (M) Release the dough mixer accessory from the supports
(C1). Release the roll and cut accessory from the supports (C2).
AFTER USE: follow the instructions described in the paragraph "Cleaning and maintenance".
GENERAL WARNING.
Remember that the safety device prevents the machine from operating when the cover of the dough mixer is not com-
pletely closed.
CLEANING AND MAINTENANCE BEFORE USE
Cleaning is the only maintenance normally required.
MOVE THE MAIN SWITCH TO THE "GREEN" POSITION AND REMOVE THE PLUG (E) FROM THE CURRENT SOCKET.
Thoroughly clean the machine with a dry cloth or soft brush.
AFTER INSTALLATION AND USE OF THE MACHINE. The cleaning operation can be completed passing a piece of dough
through the rollers (to remove any remaining dust), following the procedures described in USE OF THE MACHINE.
The same operation should be carried out for cleaning the "Sheet-cutter" accessory.
Of course the pasta used for these operations must be eliminated.
NEVER wash the machine body with water or detersives. Never wash any part of the machine in a dishwasher.
CLEANING AND MAINTENANCE AFTER USE (fig.10)
TURN THE MASTER SWITCH TO POSITION "GREEN"
MACHINE BODY.
Clean the accessory using a dry cloth or a soft brush.
DOUGH MIXER.
The dough mixer requires accurate cleaning to be carried out each component with water or a damp cloth, to
remove every residue of pasta dough. For the dismantling of the component elements of the mixer turn the knobs (N1 and N2) on the
mixer in opposite directions and remove the mixer blade (Q). Particular attention should be paid to the cleaning of the pin housings.
9