Information On Data Protection - Siemens KA D Serie Montage- Und Gebrauchsanleitung

en
Note
Press both buttons simultaneously.
2. Keep pressing Options button until "PA" is shown in
the freezer compartment display and "OF" in the
refrigerator compartment display.
3. Press + adjustment button to connect the appliance
to the app.
An animation is shown in the refrigerator
compartment display.
As soon as the refrigerator and the app are
connected, the refrigerator compartment display
shows "On".
4. Open the app and wait until the refrigerator is
displayed.
Use Add to confirm the connection between the app
and the refrigerator.
If the refrigerator is not automatically displayed, click
on Add appliance in the app and follow the
instructions. As soon as your refrigerator is
displayed, add it with +.
5. Follow the instructions in the app until the process is
complete.
The freezer compartment display shows "PA" and the
refrigerator compartment display shows "On".
The refrigerator has been connected to the app.
If the connection has failed, please check whether
the mobile device is connected to the home network
(WLAN).
Then try to establish the connection again.
If "Er" appears on the refrigerator compartment
display, reset the Home Connect settings.
Note
On reset, all Home Connect settings are reset.
Resetting Home Connect settings
If there is a problem when trying to establish a
connection or if you would like to register the appliance
in a different home network (WLAN), the Home Connect
settings can be reset:
1. Press the Super button and the adjustment button -
simultaneously.
"Cn" is shown in the freezer compartment display.
Note
Press both buttons simultaneously.
2. Keep pressing the Options button until "rE" is shown
in the freezer compartment display and "OF" is
shown in the refrigerator compartment display.
3. Press the adjustment button +.
An animation is shown in the refrigerator
compartment display for 15 seconds.
"OF" is subsequently shown in the refrigerator
compartment display.
The Home Connect settings have been reset.
Installing the Home Connect software
update
The refrigerator checks for updates to the Home
Connect software at regular intervals.
42
If an update is available, "UP" is shown in the
refrigerator compartment temperature display.
Press any button to return the display to the set
temperature.
Installing the update:
1. Press the Super button and the adjustment button -
simultaneously.
"Cn" is shown in the freezer compartment display.
Note
Press both buttons simultaneously.
2. Keep pressing the Options button until "UP" is shown
in the freezer compartment display and "OF" is
shown in the refrigerator compartment display.
3. Press the adjustment button +.
An animation is shown in the refrigerator
compartment display.
The update will be installed.
All buttons are locked during the installation.
If the installation has been completed
■
successfully, "On" is shown in the refrigerator
compartment display.
If the installation has not been completed
■
successfully, "Er" is shown in the refrigerator
compartment display.
Restart the update later on.
If the installation cannot be completed after
multiple attempts, notify Customer Service.
Customer Service access
If you contact Customer Service, they can access your
appliance and view its status after you have given your
consent. You need to have your appliance connected
to your home network for this.
Further information about Customer Service access
and its availability in your country is available under
www.home-connect.com in the Help & Support area.
1. Contact Customer Service.
2. Confirm the start of Customer Service access in the
app.
During Customer Service access the
symbol CS appears on the control panel.
3. As soon as Customer Service has obtained the
necessary data, they end access.
Note
You can interrupt remote diagnosis early by
switching off Customer Service access in the Home
Connect app.

Information on data protection

When your Home Connect refrigerator is connected for
the first time to a WLAN network that is connected to
the Internet, your appliance transmits the following
categories of data to the Home Connect server (initial
registration):
Unique appliance identification (consisting of
■
appliance codes as well as the MAC address of the
installed Wi-Fi communication module).