Display Messages - DRESTER GP 24 Bedienungsanleitung

DISPLAY MESSAGES

Error
code Text on display
C001 Main frequency
incorrect
C002 Main phase
missing
C003 Main phase
order
A004 Pump motor
overcurrent
A005 Rotation motor
overcurrent
A007 Mixer motor
overcurrent
B011 Board over
temperature
B016 Arm overcur-
rent
B017 Arm stall
A018 Fuse MF2 over-
load
A019 Fuse MF3
overload
A020 Fuse MF4
overload
A021 Fuse MF5 over-
load
A022 Fuse MF9 over-
load
A023 Pump motor
phase missing
A024 Rotation motor
phase missing
A025 Mixer motor
phase missing
A026 Pump motor off
current failure
A027 Misc sensor off
current failure
B028 Heater
undercurrent
B029 Heater
overcurrent
12
Downloaded from www.Manualslib.com
Action
Call your Sales Rep.
Check supply cable, wall
outlet and fuses.
Switch two phases in supply
plug.
Check that the pump wheel
isn't stuck. Contact your
Sales Rep.
Check that the drive roll ro-
tates smoothly. Contact your
Sales Rep.
Check that the mixer axle
runs smoothly.
Check ventilation, tem-
perature and dust around
electric box. Let the machine
cool down and try again.
Contact your Sales Rep.
Remove linear actuator and
check that the dynamic arm
runs smoothly. Contact your
Sales Rep.
Replace control card.
Check door sensor and
cable.
Check air blow solenoid
valve and cable.
Replace control card.
Look for short circuit in
cables and contacts to linear
actuator.
Check that cable to pump
motor is not damaged.
Check that cable to rotation
motor is not damaged.
Check that cable to mixer
motor is not damaged.
Call your Sales Rep.
Call your Sales Rep.
Check that cable to heater is
not damaged.
Check that cable to heater is
not damaged.
manuals search engine
GP 24
Error
code Text on display
B030 Water
temperature
sensor failure
B031 Water over
temperature
C041 Cannot read
NVM, restart
machine
A045 Cylinder 1
not retracted
A046 Cylinder 1
not extended
A047 Cylinder 2
not retracted
A048 Cylinder 2
not extended
A049 Cylinder 3
not retracted
A050 Cylinder 3
not extended
A051 Cylinder 4
not retracted
A052 Cylinder 4
not extended
A053 Cylinder 5
not retracted
A054 Cylinder 5
not extended
A055 Cylinder 6
not retracted
A056 Cylinder 6
not extended
C057 Emergency
stop activated
A060 Problem side
support
B061 Air pressure
low
A062 Trolley out of
position
C063 Terminal box
communication
loss
A064 Terminal box
MF1 overload
A065 Terminal box
MF2 overload
See chapter 11.5.9 Alarm Log
Action
Check that tempsensor
cable to heater is not dam-
aged.
Check that cable to heater is
not damaged.
Restart the machine.
Check end position
sensor 1-.
Check end position
sensor 1+.
Check end position
sensor 2-.
Check end position
sensor 2+.
Check end position
sensor 3-.
Check end position
sensor 3+.
Check end position
sensor 4-.
Check end position
sensor 4+.
Check end position
sensor 5-.
Check end position
sensor 5+.
Check end position
sensor 6-.
Check end position
sensor 6+.
Reset emergency stop
and restart machine.
Check that the side support
can move freely i.e no wheel
inside machine.
Check that compressed
air is connected.
Replace the trolley
in start position.
Check that the cable to the
terminal box is not damaged.
Check end position sensors
and pressure guard.
Check warning light,
buzzer and solenoids.
230754-EN rev.2 2017-07-13