Care And Cleaning - Scarlett SC-162 Bedienungsanleitung

· When you use the clipper for the first time, cut only small portions of hair.
· For even cutting do not force clipper. Also remember to comb the hair more frequently to remove trimmed hair
and check for uneven strands.
STEP 1 NAPE AND THE NECK
· Attach comb attachment
· Hold the clipper cutting edge pointed up and begin the haircut, starting at the center of the head at the base of
the neck (fig. 2.1).
· Hold the clipper comfortably in your hand and hold lightly against the head with the comb teeth pointing upward.
Slowly lead the clipper, working upwards and outwards, through the hair, trimming just a little at a time (fig. 2.1).
· As you cut, gradually lift the hair clipper head towards you. Continue to cut the back area from the lower part of
the neck upwards to the top of the ears.
STEP 2 BACK OF THE HEAD
· Change to the next longer comb attachment
STEP 3 SIDES OF THE HEAD
· Change to one of the shorter combs
ears.
· Then change to one of the longer combs
(fig. 2.3).
STEP 4 TOP OF THE HEAD
· Using comb attachment
which the hair normally grows (fig. 2.4). In same cases, this may require the reverse, or cutting from front to
back.
· Comb attachment
1 (3mm) or
· For longer hair on top, use the comb, provided and lift hair on the top of the head. Cut over the comb, with the
hair lifted or hold the hair between the fingers to lift it and cut it to desired length (fig. 2.5, 2.6). Always work from
the back of the head. You can cut the hair shorter gradually by reducing the space between the comb/fingers,
and the head. Comb out trimmed hair and check for uneven strands.
STEP 5 THE FINISHING TOUCHES
· Finally, use the lowest level without an attachment comb for close trimming around the base of the neck, the
sides of the neck and the ears.
· To produce a clean straight line at the sideburns, reverse the hair clipper by turning the reverse side uppermost
(fig. 2.7).
SHORT TAPERED STYLES
· Starting with the longest attachment comb
attachment comb flat against the head and slowly move the clipper through the hair, as shown (fig.8).
· Cut the hair against the direction in which it grows from the front to the crown and then level the cut with the
sides.
· To give a flat top look, the hair on top of the head must be cut over the top of a flat comb rather than by using
the attachment comb.
· Use closer cutting attachment combs to taper the hair down to the neckline as desired. Comb hair and check for
uneven areas and outlining sideboards and neckline as described previously.

CARE AND CLEANING

· Switch off the appliance and unplug it.
· Clean and oil the appliance after each use.
· Remove cut hair from the clipper with the brush enclosed.
· Wipe the cutter with a dry soft cloth.
· Oil the blades as mentioned above.
STORAGE
· Keep the appliance in a dry room.
· You may hang the cutter by provided loop.
· The blades must be oiled for storage period.
RUS
·
.
·
·
·
·
·
.
·
www.scarlett-europe.com
1 (3mm) or 2 (6mm).
3 (9mm) or
1 (3mm) or
3 (9mm) or
3 (9mm) or 4 (12mm), cut top of head from back to front along the direction in
2 (6mm) are used to achieve a close crew cut or short cut.
FLAT TOP AND SHORT CUTS
4 (12mm), cut from the back of the neck to the crown. Hold the
,
.
,
.
SC-162
4 (12mm) and cut the back of the head (fig. 2.2).
2 (6mm), trim sideburns, i.e. the hair directly in front of the
4 (12mm), and continue to cut to the top of the head
,
.
.
,
,
,
.
6
,
.
.