Optional Accessories - Makita BO6050J Betriebsanleitung

Dust nozzle
CAUTION:
Make sure the bolt is securely
tightened after installing the dust nozzle.
Otherwise the dust nozzle may fall and cause per-
sonal injury.
NOTICE:
Do not carry the tool by the dust noz-
zle. Otherwise the tool may be damaged.
You can remove the dust nozzle in accordance with the
operation.
To remove the dust nozzle, loosen the bolt, slightly open
the holder part, and remove the dust nozzle.
To install the dust nozzle, insert the mouth of the dust
nozzle into the dust outlet of the housing, align the
tongue of the holder part with the groove of the housing,
and tighten the bolt.
► Fig.11: 1. Dust nozzle 2. Dust outlet 3. Mouth
► Fig.12: 1. Holder part 2. Bolt
Dust collection (optional accessory)
► Fig.13: 1. Front cuffs 24 2. Hose 3. Dust outlet
If a Makita hose is used, you can connect the front cuffs
24 to the dust outlet directly.
OPERATION
CAUTION:
Only use Makita genuine abrasive
discs and pads for sander (optional accessories).
CAUTION:
Never switch on the tool when it
is in contact with the workpiece, it may cause an
injury to operator.
CAUTION:
Make sure the work material is
secured and stable. Falling object may cause
personal injury.
CAUTION:
Hold the tool firmly with one hand
on the switch handle and the other hand on the
front grip (or side handle) when performing the
tool.
NOTICE:
Be careful not to press down the shaft
lock button. It may shorten tool life.
NOTICE:
Never force the tool. Excessive pressure
may decrease the sanding / polishing efficiency, dam-
age the abrasive disc / pad or shorten tool life.
Sanding operation
NOTICE:
Never run the tool without the abrasive
disc. You may seriously damage the pad.
► Fig.14
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the
workpiece surface. Keep the pad flush with the work-
piece and apply slight pressure on the tool.
Polishing operation
Optional accessory
NOTICE:
Continuous operation at high speed
may damage work surface.
► Fig.15
1. Applying wax
Use the sponge pad. Apply wax to the sponge pad or work
surface. Run the tool at low speed to smooth out wax.
NOTE: First, wax a not conspicuous portion of the
work surface to make sure that the tool will not
scratch the surface or result in uneven waxing.
2. Removing wax
Use the felt pad. Run the tool to remove wax.
3.
Polishing
Apply the wool pad gently to the work surface.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool spec-
ified in this manual. The use of any other accessories
or attachments might present a risk of injury to persons.
Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Hook-and-loop type abrasive discs (with pre-
punched holes)
• Hook-and-loop type sponge pad
• Hook-and-loop type felt pad
• Hook-and-loop type wool pad
• Pad 150 (Super soft, Soft, Hard)
• Pad 130 (Polishing)
• Side grip
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
7 ENGLISH