Makita DTD171RTJ Betriebsanleitung Seite 11

2. Press and hold the button
mode-switching button at the same time until the custom-
ize lamp and the lamp of desired application mode blinks.
► Fig.11: 1. Quick mode-switching button 2. Customize lamp
NOTE: You can overwrite the current application mode
with new one by performing the procedure above.
Using the quick mode-switching function
When the tool is in the mode that is not registered, press the
quick mode-switching button to switch to the registered applica-
tion mode. The tool switches between the registered application
mode and last application mode every time you press the quick
mode-switching button. The front lamps on both sides will flash
once when switching to the registered application mode.
NOTE: The customize lamp will light up when the
application mode registered to the tool is chose.
Cancelling the quick mode-switching function
Press and hold the button
ing button at the same time until the customize lamp
and all impact force grade lamps blink.
NOTE: After cancelling the quick mode-switching function, the
quick mode-switching button works for changing the impact force.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/socket bit
► Fig.12
Use only driver bit/socket bit that has inserting portion shown
in the figure. Do not use any other driver bit/socket bit.
For tool with shallow driver bit hole
A=12mm
B=9mm
For tool with deep driver bit hole
A=17mm
B=14mm
A=12mm
B=9mm
Procedure 1
For tool without one-touch type sleeve
► Fig.13: 1. Driver bit 2. Sleeve
To install the driver bit, pull the sleeve in the direction of the
arrow and insert the driver bit into the sleeve as far as it will go.
Then release the sleeve to secure the driver bit.
For tool with one-touch type sleeve
To install the driver bit, insert the driver bit into the
sleeve as far as it will go.
and the quick
and quick mode-switch-
Use only these type of driver bit.
Follow the procedure 1. (Note)
Bit-piece is not necessary.
To install these types of driver
bits, follow the procedure 1.
To install these types of driver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.
Procedure 2
In addition to Procedure 1, insert the bit-piece into the
sleeve with its pointed end facing in.
► Fig.14: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough into
the sleeve, the sleeve will not return to its original posi-
tion and the driver bit will not be secured. In this case, try
re-inserting the bit according to the instructions above.
NOTE: When it is difficult to insert the driver bit, pull the
sleeve and insert it into the sleeve as far as it will go.
NOTE: After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.
Installing hook
CAUTION:
When installing the hook, always
secure it with the screw firmly. If not, the hook may
come off from the tool and result in the personal injury.
► Fig.15: 1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
OPERATION
► Fig.16
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in the figures.
Proper fastening torque for standard bolt
N•m
(kgf•cm)
140
(1428)
120
(1224)
100
(1020)
80
(816)
2
60
(612)
40
(408)
20
(204)
0
1. Fastening time (second) 2. Fastening torque
11 ENGLISH
M16
M14
M16
M12
M14
M10
M12
M8
M10
M8
1 2
1