Seite 1
Quick Start Guide Guía de inicio rápido Guida di riferimento rapido Kurzanleitung Guide de démarrage rapide Cisco Small Business 300 Series Managed Switches Downloaded from www.Manualslib.com manuals search engine...
Seite 2
Welcome Thank you for choosing the Cisco 300 Series Managed Switch, a Cisco Small Business network communications device. This device is designed to be operational right out of the box as a standard bridge. In the default configuration, it will forward packets between connecting devices after power up.
The switch should have a minimum of 5 inches (130 mm) of clearance on all sides. Insecure mounting may damage the device or cause injury. ARNING Cisco is not responsible for damages incurred by insecure wall- mounting. 300 Series Managed Switches Downloaded from www.Manualslib.com...
Seite 4
Ethernet ports. The LED of the port lights if the device connected is active. Refer to Features of the Cisco Small Business Managed Switch, page 10 for details about the different ports and LEDs on each switch.
Seite 5
Configuring the Cisco Small Business Managed Switch Before You Begin Verify that a computer with Microsoft Internet Explorer (version 6 and higher) or Firefox (version 2.0 or higher) is available. The switch can be accessed and managed by two different methods; over your IP network using the web-based interface, or by the menu CLI through the console port.
Seite 6
The Managed Switch Login Page displays. Enter the default login information: Username is cisco Default password is cisco (passwords are case sensitive) If this is the first time that you have logged on with the default Change Password Page username and password, the opens.
Seite 7
• Save your settings • Return your computer to its original settings These tasks can be accomplished by using the procedures in the Cisco Small Business Managed Switch Administration Guide. 300 Series Managed Switches Downloaded from www.Manualslib.com...
Seite 8
Troubleshoot Your Connection If you cannot access your switch from the web-based interface, the switch may not be reachable from your computer. You can test network connections by using ping on a computer running Windows: Open a command window by using Start > Run and enter cmd. At the Command window prompt enter ping and the managed switch IP address.
Seite 9
No IP route: If the switch and your computer are in different IP subnets, you need one or more routers to route the packets between the two subnets. Unusually long access time: Due to the standard spanning tree loop detection logic, adding new connections may take 30 to 60 seconds for the affected interfaces and/or LAN to become operational.
Seite 10
• MiniGBIC ports are compatible with Cisco miniGBIC modules MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1, and MFEBX1, as well as other brands of miniGBIC modules.
PoE (if present)—(Amber) Located on the right of the port. Lights steady to indicate that power is being supplied to a device attached to the corresponding port. 100M LED (if present)—(Green) Located on the right of the port. Lights steady when another device is connected to the port, is powered on, and a 100 Mbps link is established between the devices.
Seite 12
Returning the Device to the Factory Default Settings To use the Reset button to reboot or reset the managed switch, do the following: • To reboot the managed switch, press the Reset button for less than 10 seconds. • To restore the managed switch configuration to the factory default settings: 1.
Seite 13
Cisco Small Business Firmware www.cisco.com/go/smallbizfirmware Downloads Select a link to download firmware for Cisco Small Business Products. No login is required. Downloads for all other Cisco Small Business products, including Network Storage Systems, are available in the Download area on Cisco.com at...
Seite 14
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners.
Seite 15
300 Series Managed Switches Downloaded from www.Manualslib.com manuals search engine...
Guía de inicio rápido Cisco Small Business 300 Series Managed Switches Downloaded from www.Manualslib.com manuals search engine...
Seite 17
Bienvenido Gracias por elegir el Cisco 300 Series Managed Switch, un dispositivo de comunicaciones de red Cisco Small Business. Este dispositivo está diseñado y configurado de fábrica para que funcione como un puente estándar. En la configuración predeterminada, reenviará paquetes entre los dispositivos de conexión tras el encendido.
Seite 18
Un montaje poco firme puede dañar el dispositivo o provocar DVERTENCIA lesiones. Cisco no se hace responsable de los daños que se produzcan debido a un montaje en pared poco firme. 300 Series Managed Switches Downloaded from www.Manualslib.com...
Seite 19
Cisco recomienda usar Cat5 o un cable superior para la conectividad Gigabit. Al conectar los dispositivos de red, no exceda la distancia de cableado máxima de 328 pies (100 metros). Los dispositivos adjuntos o la red LAN pueden tardar un minuto en funcionar luego de ser conectados.
Seite 20
Configuración del Cisco Small Business Managed Switch Antes de comenzar Asegúrese de contar con una computadora con Microsoft Internet Explorer (versión 6 y superior) o Firefox (versión 2.0 o superior). Existen dos métodos para obtener acceso al switch y administrarlo; a través de la red IP mediante la utilidad de configuración de switch inteligente...
Seite 21
Introduzca la información de inicio de sesión predeterminada: El nombre de usuario es cisco La contraseña predeterminada es cisco (las contraseñas distinguen entre mayúsculas y minúsculas) Si es la primera vez que inicia sesión con el nombre de usuario y la contraseña predeterminados, se abre la...
Seite 22
Guarde la configuración. • Restaure la configuración original de la computadora Estas tareas pueden realizarse a través de los procedimientos que se encuentran en la Guía de administración para el Cisco Small Business Managed Switch. 300 Series Managed Switches Downloaded from www.Manualslib.com...
Seite 23
Troubleshooting de conexión Si no puede obtener acceso al switch desde la utilidad de configuración de switch inteligente basada en la Web, es posible que no pueda acceder al switch desde la computadora. Puede probar las conexiones de red al utilizar el comando ping en una computadora que ejecute Windows: Abra una ventana de comando al utilizar Start (Inicio) >...
Seite 24
Dirección IP equivocada: Asegúrese de estar usando la dirección IP correcta del switch. Puede determinar el estado de la ubicación donde recibió la dirección IP actual del switch desde el indicador LED del sistema. Puede determinar la dirección IP actual del switch desde el menú CLI a través de la interfaz del puerto de la consola, o desde el administrador de red.
Seite 25
• Los puertos MiniGBIC son compatibles con los módulos miniGBIC MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1 y MFEBX1 de Cisco, además de otras marcas de módulos miniGBIC. • La interfaz MiniGBIC es un puerto de combinación, compartido con otra interfaz RJ-45. Si el MiniGBIC está activo, el puerto RJ-45 adyacente está...
PoE (si hubiera): (ámbar) ubicado del lado derecho del puerto. Se enciende de forma permanente para indicar que el dispositivo conectado al puerto correspondiente recibe energía. Indicador 100M (si hubiera): (verde) ubicado del lado derecho del puerto. Se enciende de forma permanente si hay otro dispositivo conectado al puerto, si está...
Seite 27
Cómo restablecer la configuración predeterminada de fábrica del dispositivo Para usar el botón Reset (Restablecer) para reiniciar el managed switch, haga lo siguiente: • Para reiniciar el managed switch, presione el botón Reset (Restablecer) durante 10 segundos aproximadamente. • Para restaurar los valores predeterminados de fábrica de la configuración del managed switch: 1.
Seite 28
Cómo seguir Asistencia técnica Comunidad de asistencia www.cisco.com/go/smallbizsupport técnica de Cisco para la PYME Soporte y recursos de Cisco www.cisco.com/go/smallbizhelp Small Business Contactos de asistencia técnica www.cisco.com/en/US/support/tsd_cisco_ telefónica small_business_support_center_contacts.html Descargas de firmware de www.cisco.com/go/smallbizfirmware Cisco Small Business Seleccione un vínculo para descargar firmware para los productos Cisco Small Business.
Seite 29
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners.
Descrizione generale Grazie per aver scelto lo switch gestito Cisco serie 300, un dispositivo di comunicazioni di rete di Cisco Small Business. Questo dispositivo è concepito per essere operativo out-of-the-box come ponte standard. Nella configurazione predefinita, dopo l'accensione, lo switch reindirizza i pacchetti tra i dispositivi di connessione.
Lo switch dovrebbe avere uno spazio libero di almeno 130 mm (5 pollici) su tutti i lati. Un montaggio instabile può danneggiare il dispositivo o TTENZIONE causare infortuni. Cisco non si riterrà responsabile di danni causati da un montaggio a parete instabile. Switch gestiti serie 300 Downloaded from www.Manualslib.com...
Seite 33
ASSAGGIO che si desidera connettere allo switch gestito. Cisco raccomanda l'utilizzo di Cat5 o di un cavo migliore per la connessione Gigabit. Quando si collegano i dispositivi di rete, non superare la lunghezza massima dei cavi pari a 100 metri (328 piedi).
Seite 34
Come configurare lo switch gestito Cisco Small Business Operazioni preliminari Verificare la disponibilità di un computer con Microsoft Internet Explorer (versione 6 e successiva) o Firefox (versione 2.0 o successiva). È possibile accedere e gestire lo switch in due modi diversi: tramite la rete IP utilizzando l'utilità...
Seite 35
Verrà visualizzata la pagina di accesso dello switch gestito. Inserire le informazioni predefinite di accesso: ASSAGGIO Il nome utente è cisco La password predefinita è cisco (le password fanno distinzione tra maiuscole e minuscole) Se si tratta del primo accesso con il nome utente e la ASSAGGIO password predefiniti, verrà...
Seite 36
Inserire nome utente e password. Nome utente e password ASSAGGIO fanno distinzione tra maiuscole e minuscole e sono alfanumerici. Il nome utente predefinito è cisco e la password predefinita è cisco. Se si tratta del primo accesso con il nome utente e la...
Seite 37
Risoluzione dei problemi relativi alla connessione Se non è possibile accedere allo switch dall'utilità di configurazione intelligente dello switch basata sul Web, lo switch potrebbe non essere raggiungibile dal computer. È possibile verificare le connessioni di rete utilizzando il comando ping su un computer con sistema operativo Windows: Selezionare Start >...
Seite 38
Indirizzo IP sbagliato: Assicurarsi di utilizzare l'indirizzo IP corretto dello switch. È possibile determinare lo stato del punto in cui è stato ricevuto l'indirizzo IP corretto dello switch dal LED del sistema. È possibile determinare l'indirizzo IP corrente dello switch dal CLI del menu tramite l'interfaccia della porta Console oppure dall'amministratore di rete.
Seite 39
• Le mini porte di conversione dell'interfaccia Gigabit sono compatibili con i moduli Cisco mini-GBIC MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1 e MFEBX1 oltre ad ulteriori marchi di moduli mini-GBIC.
PoE (se presente) (ambra). Posizionato sulla destra della porta. Si illumina per indicare che l'alimentazione viene fornita a un dispositivo associato alla porta corrispondente. LED 100M (se presente) (verde). Posizionato sulla destra della porta. Si illumina quando un altro dispositivo è connesso alla porta, quando è acceso e quando viene stabilito un collegamento a 100 Mbps tra i dispositivi.
Seite 41
Come ripristinare le impostazioni predefinite del dispositivo Per utilizzare il pulsante Ripristina per riavviare o reimpostare lo switch gestito, eseguire le seguenti operazioni: • Per riavviare lo switch gestito, premere il pulsante Ripristina per meno di 10 secondi. • Per ripristinare le impostazioni predefinite dello switch gestito: 1.
Seite 42
Selezionare un collegamento per scaricare il firmware relativo ai prodotti Cisco Small Business. Non sono necessari dati di accesso. I download per tutti gli altri prodotti Cisco Small Business, inclusi i sistemi di memorizzazione di rete, sono disponibili nell'area Download su Cisco.com del sito www.cisco.com/go/software...
Seite 43
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners.
Seite 44
Kurzanleitung Cisco Small Business 300 Series Managed Switches Downloaded from www.Manualslib.com manuals search engine...
Seite 45
Willkommen Vielen Dank, dass Sie sich für den Cisco 300 Series Managed Switch, ein Netzwerkkommunikationsgerät von Cisco Small Business, entschieden haben. Dieses Gerät ist vorkonfiguriert und sofort als Standard-Bridge einsatzbereit. In der Standardkonfiguration überträgt das Gerät nach dem Einschalten Pakete zwischen den angeschlossenen Verbindungsgeräten.
Der Switch sollte zu allen Seiten einen Freiraum von 130 mm besitzen. Eine unsachgemäße Befestigung kann das Gerät beschädigen ARNUNG oder zu Verletzungen führen. Cisco übernimmt keine Verantwortung für Schäden, die durch eine unsachgemäße Wandbefestigung entstehen. 300 Series Managed Switches Downloaded from www.Manualslib.com...
Die LED des Ports leuchtet auf, wenn das angeschlossene Gerät aktiv ist. Informationen zu den unterschiedlichen Ports und LEDs an jedem Switch finden Sie unter Funktionen des Managed Switch von Cisco Small Business auf Seite Wiederholen Sie Schritt 1 Schritt 2 für jedes Gerät, das...
Konfigurieren des Managed Switch von Cisco Small Business Vorbereitung Vergewissern Sie sich, dass Sie über einen Computer mit Microsoft Internet Explorer (Version 6 oder höher) oder Firefox (Version 2.0 oder höher) verfügen. Für den Zugriff auf den Switch und für dessen Verwaltung gibt es zwei unterschiedliche Möglichkeiten: über Ihr IP-Netzwerk mit dem webbasierten...
Seite 49
Die Managed Switch-Anmeldeseite wird angezeigt. Geben Sie die Standard-Anmeldeinformationen ein: CHRITT Der Benutzername lautet cisco Das Standardkennwort lautet cisco (bei Kennwörtern wird zwischen Groß- und Kleinschreibung unterschieden) Wenn Sie sich zum ersten Mal mit dem Standardbenutzernamen CHRITT Seite „Kennwort ändern“...
Seite 50
IP-Adresse und die Subnetzmaske entsprechend Ihrer Netzwerktopologie. • Speichern Ihrer Einstellungen • Wiederherstellen der ursprünglichen Computereinstellungen Die Vorgehensweisen für diese Aufgaben sind im Administratorhandbuch für den Managed Switch von Cisco Small Business beschrieben. 300 Series Managed Switches Downloaded from www.Manualslib.com manuals search engine...
Fehlerbehebung an der Verbindung Wenn Sie mit dem webbasierten Konfigurationsdienstprogramm nicht auf Ihren Switch zugreifen können, ist der Switch für Ihren Computer möglicherweise nicht erreichbar. Sie können Netzwerkverbindungen mit ping auf Computern testen, auf denen Windows ausgeführt wird: Wählen Sie Start > Ausführen, um ein Eingabeaufforderungsfenster CHRITT zu öffnen, und geben Sie cmd ein.
Seite 52
Falsche IP-Adresse: Stellen Sie sicher, dass Sie für den Switch die richtige IP-Adresse verwenden. Sie können an der System-LED erkennen, wo Sie die aktuelle IP-Adresse des Switch erhalten haben. Sie können die aktuelle IP-Adresse des Switch im Menü CLI über die Konsolen-Port-Schnittstelle ermitteln oder bei Ihrem Netzwerkadministrator erfragen.
Managed Switch über einen Lichtwellenleiter eine Uplink-Verbindung mit anderen Switches herstellen kann. • MiniGBIC-Ports sind kompatibel mit den MiniGBIC-Modulen MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1 und MFEBX1 von Cisco sowie mit MiniGBIC-Modulen anderer Hersteller. • Die MiniGBIC-Schnittstelle ist ein Mehrfach-Port, der mit einer anderen RJ-45-Schnittstelle geteilt wird.
PoE (sofern vorhanden) — (Bernsteinfarben) Auf der rechten Seite des Ports. Diese LED leuchtet kontinuierlich und zeigt an, dass das Gerät, welches an den entsprechenden Port angeschlossen ist, mit Spannung versorgt wird. 100M LED (sofern vorhanden) — (Grün) Auf der rechten Seite des Ports. Diese LED leuchtet kontinuierlich, wenn ein anderes Gerät an den Port angeschlossen und eingeschaltet ist und eine 100 Mbps-Verbindung zwischen den Geräten besteht.
Wiederherstellen der Werkseinstellungen des Geräts Gehen Sie folgendermaßen vor, um mit der Reset-Taste einen Neustart durchzuführen oder den Managed Switch auf die Werkseinstellungen zurückzusetzen: • Um einen Neustart des Managed Switch durchzuführen, drücken Sie die Taste Reset für weniger als 10 Sekunden. •...
Cisco Small Business Firmware- www.cisco.com/go/smallbizfirmware Downloads Wählen Sie einen Link für den Download von Firmware für Cisco Small Business-Produkte aus. Eine Anmeldung ist nicht erforderlich. Downloads für alle anderen Cisco Small Business-Produkte, einschließlich Netzwerkspeichersysteme, stehen im Download-Bereich von Cisco.com unter www.cisco.com/go/software zur Verfügung (Registrierung/Anmeldung erforderlich).
Seite 57
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners.
Guide de démarrage rapide Cisco Small Business Commutateurs administrables Série 300 Downloaded from www.Manualslib.com manuals search engine...
Seite 59
Bienvenue Merci d’avoir choisi le commutateur géré Cisco300, un appareil de communication en réseau de Cisco Small Business. Cet appareil est conçu pour être directement opérationnel en tant que pont standard. Dans sa configuration par défaut, il transfère des paquets entre des appareils connectés après sa mise sous tension.
Vous devez laisser un espace minimum de 130 mm (5 po) de chaque côté. Tout montage non conforme peut endommager l’appareil ou VERTISSEMENT entraîner des blessures. Cisco ne peut en aucun cas être tenu responsable de tout dommage découlant d’un montage mural non conforme.
Seite 61
É TAPE voulez relier au commutateur administrable. Cisco vous recommande vivement d’utiliser un câble de EMARQUE catégorie 5 ou supérieure pour la connectivité Gigabit. Lorsque vous connectez vos appareils de réseautique, ne dépassez pas la distance de câblage maximale, qui est de 100 mètres (328 pieds).
Seite 62
Configuration du Commutateur administrable Cisco Small Business Avant de commencer Veillez à disposer d’un ordinateur doté de Microsoft Internet Explorer (version 6 ou ultérieure) ou de Firefox (version 2.0 ou ultérieure). Deux méthodes s’offrent à vous pour accéder au commutateur et le gérer : sur votre réseau IP en vous servant de l’utilitaire intelligent de configuration de...
Seite 63
Entrez les informations d’ouverture de session par défaut : É TAPE Nom d’utilisateur : cisco Mot de passe par défaut : cisco (Les mots de passe font la distinction majuscules/minuscules.) S’il s’agit de votre première ouverture de session avec le nom É...
Seite 64
Le nom d’utilisateur par défaut est cisco, tout comme le mot de passe par défaut. S’il s’agit de votre première ouverture de session avec le nom É...
Seite 65
Dépannage de votre connexion Si vous ne parvenez pas à accéder à votre commutateur à partir de l’utilitaire intelligent de configuration de commutateur en ligne, il est possible que le commutateur ne soit pas accessible depuis l’ordinateur. Vous pouvez tester les connexions réseau en utilisant la commande ping sur un ordinateur exécutant Windows: Ouvrez une fenêtre de commande en sélectionnant Démarrer >...
Seite 66
Adresse IP erronée : Assurez-vous que vous utilisez l’adresse IP appropriée pour le commutateur. Vous pouvez déterminer le statut de l’origine de l’adresse IP actuelle du commutateur à partir de la LED système. Vous pouvez déterminer l’adresse IP actuelle du commutateur à partir de l’interface de ligne de commande via l’interface du port console, ou la demander à...
Seite 67
MiniGBIC. Le commutateur administrable peut ainsi établir une liaison montante vers d’autres commutateurs via une fibre optique. • Les ports MiniGBIC sont compatibles avec les modules MiniGBIC Cisco MGBSX1, MGBLH1, MGBLX1, MGBBX1, MFELX1, MFEFX1 et MFEBX1, ainsi qu’avec des modules MiniGBIC d’autres marques.
PoE (si disponible) : (orange) située sur la droite du port. Reste allumée pour indiquer qu’un appareil relié au port correspondant est alimenté. LED 100M (si disponible) : (verte) située sur la droite du port. Reste allumée lorsqu’un autre appareil est connecté au port, et est mis sous tension, et qu’une liaison de 100 Mbits/s est établie entre les appareils.
Seite 69
Restauration de la configuration d’origine de l’appareil Pour utiliser le bouton Reset afin de redémarrer ou de réinitialiser le commutateur administrable, procédez comme suit: • Pour redémarrer le commutateur administrable, appuyez sur le bouton Reset pendant moins de dix secondes. •...
Cisco Small Sélectionnez un lien pour télécharger le Business micrologiciel d’un produit Cisco Small Business. Aucune ouverture de session n’est requise. Les téléchargements se rapportant à tous les autres produits Cisco Small Business, et notamment les unités de stockage réseau, sont disponibles dans la zone de téléchargement de Cisco.com, à...
Seite 71
Commutateurs administrables Série 300 Downloaded from www.Manualslib.com manuals search engine...
Seite 72
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners.